水悬浮体系中三单体接枝聚丙烯的改性
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

TQ325.14

基金项目:

黑龙江省科技攻关项目(GZ06A402)


Modification of Ternary-Monomer Grafting onto Polypropylene in Water Suspension System
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    在水悬浮体系中,经自由基引发聚丙烯(PP)与马来酸酐(MAH)、苯乙烯(ST)及丙烯酸丁酯(BA)接枝聚合制备接枝产物(PP-g-PMSB),同时体系中产生了非接枝的聚合物(PMSB′)。结果表明,随单体含量增加,接枝率和PMSB′含量升高,且在接枝率高于5.25%时出现微量凝胶。三单体以长支链形式接枝到PP主链上,随接枝率的增加,PP-g-PMSB热稳定性和极性提高,熔体流动速率减小。接枝率5.50%时,PP-g-PMSB水接触角为79.52°;PMSB′含量3.25%时,水接触角降低至69.62°。

    Abstract:

    Polypropylene(PP) was grafted with methyl methacrylate(MAH),styrene(ST) and butyl acrylate(BA) via the free radical polymerization leading to PP-g-PMSB and non-graft polymer(PMSB′) in water suspension system.The results indicate that the graft ratio of PP-g-PMSB and content of PMSB′ increases as the monomer content increases,and when the graft ratio of the product PP-g-PMSB is above 5.25%,the traces of gel are seen generated.All these ternary-monomers are grafted onto PP as longer chain branches.The thermal stability and polarity of PP-g-PMSB increase along with the increase of graft ratio,but the melt flow rate decreases.The water contact angle of the PP-g-PMSB is 79.52° when graft ratio is 5.50%,decreases to 69.62° with 3.25% PMSB′.

    参考文献
    相似文献
    引证文献
引用本文

祝宝东,王鉴,董群,宋军.水悬浮体系中三单体接枝聚丙烯的改性[J].高分子材料科学与工程,2012,28(1):67-70.

复制
分享
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2013-04-16
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@163.net; gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2024 版权所有
技术支持:北京勤云科技发展有限公司