气辅共挤出流道中聚合物流动过程的数值分析
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

TQ311

基金项目:

国家自然科学基金资助项目(51103080);山东大学自主创新基金资助项目(2010TS096)


The Numerical Analysis of the Polymer Melts Flow Through the Gas Assisted Coextrusion Die
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    建立了气辅条件下两种聚合物在矩形流道中共挤出流动的三维非等温数值分析模型。用粘弹性流体模型(PTT模型)描述熔融聚合物的特性,Arrhenius方程表示流动对温度的依赖性,并且考虑聚合物相对于流道壁面的滑移以及不相容聚合物熔体间滑移的边界条件。用有限元方法数值模拟了聚合物成型过程,将计算结果与普通共挤出成型流动进行了对比分析。结果表明,气垫层的加入,将使聚合物熔体的压力降减低20%~40%;使流道出口处的速度场分布均匀,速度场的最大值下降约50%;气垫区聚合物的自由流动还将对共挤出界面的形状和位置有一定的影响。

    Abstract:

    The three-dimensional non-isothermal numerical simulation model of two polymers flow through the rectangle path on the condition of gas assisted was founded.The polymer melts obey a differential constitutive equation(Phan-Thien and Tanner model).The temperature-dependent transport properties were taken into account and were expressed by the Arrhenius equation.The slipping boundary condition near the die wall and between the two polymers was also considered.The gas assisted coextrusion process was analyzed by using the finite element method.The simulated results of the gas assisted coextrusion and the general coextrusion were analyzed contrastively.It is found that the gas assisted mechanism influences the fluid process greatly.The pressure dropping falls 20%~40%.The velocity distribution at the exit is more uniform.The maximum value of the velocity descends about 50%.The shape and the location of the polymer interface are also changed due to the gas zone.

    参考文献
    相似文献
    引证文献
引用本文

张敏,黄传真,贾玉玺.气辅共挤出流道中聚合物流动过程的数值分析[J].高分子材料科学与工程,2012,28(1):176-179.

复制
分享
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2013-04-16
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@163.net; gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2024 版权所有
技术支持:北京勤云科技发展有限公司