熔融静电纺聚对苯二甲酸乙二酯超细纤维的制备及工艺优化
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家高技术研究发展计划(863)资助项目(2012AA030313);2012江苏科技支持计划(工业)项目(SBE201201094)


Preparation and Process Optimization of Poly(Ethylene Terephthalate) Ultrafine Fibers by Melt-Electrospinning
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    采用熔融静电纺丝法制备了聚对苯二甲酸乙二酯(PET)超细纤维膜,应用正交试验分析了纺丝主要工艺参数对熔融电纺PET超细纤维直径的影响。实验表明,在本实验装置条件下可实现熔融电纺工艺的有效调控,纤维直径随着纺丝电压的升高呈现下降的趋势;纤维随接收距离的增加和熔体温度的上升均表现为先变细后变粗;喂料气压的增加会增大纤维直径;提高纺丝环境温度至聚合物的玻璃化转变温度,纤维平均直径明显下降。在最佳纺丝工艺条件下(纺丝电压27 kV,接收距离7 cm,熔体温度255 ℃,环境温度70 ℃,依靠聚合物自重喂给)制备的PET超细纤维均直径小于1 μm。

    Abstract:

    Poly(ethylene terephthalate) (PET) ultrafine fibers were prepared by melt electrospinning technology, and the effects of main spinning parameters on the fibers diameter were described through orthogonal experiment. The results show that under the condition of this experiment device, the effective control of melt-electrospinning process can be realized, the diameters of the fiber present downward trend with increase of the spinning voltage; the fibers diameter gets thinner first and then gets thicker with increase of the accepted distance as well as the melt temperature; increasing in the feed pressure would increase the fibers diameter; improving spinning environmental temperature to glass transition temperature of the polymer, the average fibers diameter decreases significantly. The diameter of PET ultrafibers prepared under the condition of the optimized spinning process(spinning voltage 27 kV, accepted distance 7 cm, melt temperature 260 ℃, environmental temperature 70 ℃, fed by itself mass) is less than 1 μm on average.

    参考文献
    相似文献
    引证文献
引用本文

王宏, 徐阳, 王肖娜, 杜远之, 李莘.熔融静电纺聚对苯二甲酸乙二酯超细纤维的制备及工艺优化[J].高分子材料科学与工程,2014,30(9):122-127.

复制
分享
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2014-09-22
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@163.net; gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2024 版权所有
技术支持:北京勤云科技发展有限公司