基于ANSYS CFX的注塑成型充填过程三维模拟
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

TQ320.662

基金项目:

‘十一五’国家科技支撑计划项目(2006BAF04B12)


3D Simulation of Filling Stage in Injection Molding Based on ANSYS CFX
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    注塑成型中,熔体在模腔内的流动为非牛顿流体在复杂型腔内的非等温、非稳态流动。充填过程的三维数值模拟能更真实地模拟熔体在型腔内的三维流动状态。本文采用有限元分析软件ANSYS CFX进行二次开发,实现注塑成型充填过程的三维模拟,可求解熔体前沿、压力场、温度场等一系列模拟结果。模拟结果与注塑成型软件MOLDFLOW结果进行对比,验证了该方法的有效性。算例分析结果表明,对于薄壁制品,基于中面模型的注塑成型模拟方法是适用的,但对于非薄壁制品,采用三维模拟方法可以得到更合理更全面的信息。

    Abstract:

    In injection molding,the non-Newtonian viselastic fluid flows in complex cavity under non-isothermal condition,3D simulation can describe the flow behavior of the polymer melt accurately,ANSYS CFX was adopted to implement the 3D filling simulation of injection molding,and the melt front,pressure and temperature fields during injection molding were simulated.The simulation results were verified by comparing the results of MOLDFLOW and ANSYS CFX.The analysis of simulation results indicates that Hele-shaw flow is suitable for simulating the thinwall part,but the 3D model can describe the flow phenomena for the thick wall part.

    参考文献
    相似文献
    引证文献
引用本文

焦令宽,王利霞,李倩,申长雨.基于ANSYS CFX的注塑成型充填过程三维模拟[J].高分子材料科学与工程,2012,28(3):156-160. Lingkuan Jiao, Lixia Wang, Qian Li, Changyu Shen.3D Simulation of Filling Stage in Injection Molding Based on ANSYS CFX[J]. Polymer Materials Science & Engineering,2012,28(3):156-160.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2013-04-16
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司