部分动态预硫化对EPDM发泡行为的影响
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

TQ328.9

基金项目:

湖北省自然科学基金资助项目(2005ABA055)


The Effect of Partially Dynamic Vulcanization on the Foaming of EPDM
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    采用部分动态预硫化工艺制备三元乙丙橡胶(EPDM)发泡材料,即通过在哈克中动态预硫化来控制橡胶预交联,然后混入相同的硫化和发泡剂体系并制得发泡材料。研究了部分动态预硫化对EPDM凝胶含量及发泡行为的影响。结果表明,动态预硫化过程中,随硫磺用量增加,其最终平衡扭矩升高,预硫化混炼胶的凝胶含量增加;硫化和发泡行为测量表明,动态预硫化并未影响EPDM混炼胶二次硫化速度以及发泡剂分解速度;扫描电镜(SEM)显示,预硫化阶段硫磺用量为0.0125phr时的试样,能获得较好的泡孔结构和较低的密度,表明适量的预硫化能明显改善EPDM混炼胶的发泡行为。

    Abstract:

    This study has developed a new way of rubber foam preparation using partially dynamic vulcanization technology.The partially precure in HAAKE is used to control the degree of ethylene-propylene-diene rubber(EPDM) compound pre-crosslinking.The final torque increases with sulphur content increasing,which shows that the crosslink density of precured EPDM compound could be effectively regulated by adding sulphur.The gel content increases with pre-crosslinking degree increasing.Rheometric measurement shows that the rate of vulcanization of partially precured EPDM compound is not affected by the precure in the HAAKE rheometer.The blowing results show that the foam processability could be improved and the expansion ratio increases in the same processing condition for optimum partially precured EPDM compound,which indicates the efficiency of blowing agent azodicarbonamide(AC) could be enhanced.Scanning electron microscope(SEM) results show that the foam articles of optimum partially precured EPDM compound have a regular cell structure.

    参考文献
    相似文献
    引证文献
引用本文

王必勤,李纯清,刘璐,严海彪.部分动态预硫化对EPDM发泡行为的影响[J].高分子材料科学与工程,2012,28(6):110-113. Biqin Wang, Chunqing Li, Lu Liu, Haibiao Yan. The Effect of Partially Dynamic Vulcanization on the Foaming of EPDM[J]. Polymer Materials Science & Engineering,2012,28(6):110-113.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2013-04-16
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司