烯基琥珀酸酐改性MS-1淀粉及表面施胶实验
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

TS727.5

基金项目:

国家自然科学基金资助项目(50973057;20876093);陕西省自然科学专项基金资助项目(2010JK436);陕西科技大学科研启动基金项目(BJ11-10);陕西科技大学研究生创新基金资助项目


Alkenyl Succinic Anhydride Modified MS-1 Starch as Surface Sizing Agent
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    采用烯基琥珀酸酐(ASA)对MS-1淀粉在湿法条件下进行改性,在MS-1淀粉上引进疏水基团,合成一种新型的淀粉表面施胶剂。探讨了反应过程中反应温度、反应物比例、反应时间对施胶效果的影响。结果表明,其最佳合成工艺条件是,反应温度65℃,m(MS-1淀粉)∶m(ASA)=5∶1,反应时间2h。当施胶质量分数为5%时,施胶度可达206s。并利用红外光谱分析仪、表面张力仪、接触角测定仪、扫描电子显微镜对ASA改性MS-1淀粉的结构与性能进行了表征。红外图谱表明,产物在1569 cm-1出现酯羰基的吸收峰,说明ASA与MS-1淀粉发生了酯化反应。当施胶质量分数为5%时,接触角达133°。

    Abstract:

    A type of starch surface sizing agent was synthesized by modifying MS-1 starch with alkenyl succinic anhydride(ASA) in aqueous slurry systems to introduce hydrophobic groups to MS-1 starch.Effects of reaction temperature,reactant ratios,reaction time on sizing effect were studied.The results indicate that the suitable parameters for the preparation are as follows: reaction temperature is 65 ℃,the mass ratio of MS-1 starch to ASA is 5∶1,reaction period is 2.0h.The sizing degrees can reach 206s when the sizing mass fraction is 5%.The structure and properties of the products were determined by the Fourier transform infrared spectra(FT-IR),surface tensiometer,contact angle cryoscope and scanning electron microscope(SEM).IR spectrum showed that a absorption peak appeared at 1569 cm-1 indicating that esterification reaction happened between ASA and MS-1 starch.The contact angle was 133° when the sizing mass fraction was 5%.

    参考文献
    相似文献
    引证文献
引用本文

黄芳,李小瑞,杨晓武,李培枝.烯基琥珀酸酐改性MS-1淀粉及表面施胶实验[J].高分子材料科学与工程,2012,28(6):138-141. Fang Huang, Xiaorui Li, Xiaowu Yang, Peizhi Li. Alkenyl Succinic Anhydride Modified MS-1 Starch as Surface Sizing Agent[J]. Polymer Materials Science & Engineering,2012,28(6):138-141.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2013-04-16
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司