工艺参数对短玻璃纤维增强PP复合材料注射压力和翘曲变形的影响
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

TQ320.662

基金项目:


Influence of Processing Parameters on Injection Pressure and Warpage of Short-Glass Fiber Reinforced PP Injection-Molded Part
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    采用Moldflow对聚丙烯及其短玻璃纤维增强复合材料的注塑成型过程进行3D模拟分析,基于Taguchi试验设计方法(DOE),采用L16(45)正交矩阵进行试验设计,研究工艺参数对注射压力和翘曲变形的影响。结果表明,纤维含量对注射压力和翘曲变形影响作用较为显著,且存在最佳值;模具温度、熔体温度、保压时间和保压压力对注射压力的影响为单调的线性关系,但其对翘曲变形的影响较复杂。

    Abstract:

    In this paper,the three dimensional numerical simulation was carried out for the mold-filling stage of injection molding of polypropylene(PP) and short-glass fiber reinforced PP by means of moldflow software.Based on Taguchi design of experiments(DOE) method and using an L16(45)orthogonal array,the influence of processing parameters on injection pressure and warpage was investigated.It is shown that the fiber content has a significant effect on the injection pressure and warpage,and has an optimal value.The effects of mould temperature,melt temperature,holding time and holding pressure on injection pressure are monotonous linear,but on warpage defection is complicate.

    参考文献
    相似文献
    引证文献
引用本文

熊爱华,柳和生,黄兴元,黄益宾,江青松,赖家美.工艺参数对短玻璃纤维增强PP复合材料注射压力和翘曲变形的影响[J].高分子材料科学与工程,2012,28(6):163-168. Aihua Xiong, Hesheng Liu, Xingyuan Huang, Yibin Huang, Qingsong Jiang, Jiamei Lai. Influence of Processing Parameters on Injection Pressure and Warpage of Short-Glass Fiber Reinforced PP Injection-Molded Part[J]. Polymer Materials Science & Engineering,2012,28(6):163-168.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2013-04-16
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司