熔体温度对注塑成型iPP制品结晶形态的影响
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

TQ320.662

基金项目:

2010年河南省重大公益项目(HNZB[2010]N91);高等学校博士点专项科研基金(20094101110008)


Influence of Melt Temperature on the Morphology Evolution of Injection Molded Isotactic Polypropylene Parts
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    注塑成型聚丙烯制品的内部结晶形态对制品的最终性能起着至关重要的作用,而结晶形态的形成对成型条件(尤其是熔体温度)有一定依赖性。文中利用偏光显微镜、小角X射线散射和广角X射线衍射等实验方法,详细研究了熔体温度对注塑成型iPP制品结晶形态的影响。研究结果表明,在实验温度范围内,制品厚度方向形态呈现五层皮芯结构,即冷冻层、过渡层、剪切层、β晶层、α球晶层。随着熔体温度提高,皮层厚度减小;结晶度提高,取向度极大值并无明显变化。

    Abstract:

    For injection molding of isotactic polypropylene(iPP) products,the internal crystalline morphology plays a major role in the final properties,and the formation of the crystalline morphology depends on the molding conditions,especially on melt temperature.In this work,the effects of melt temperature on the morphology evolution of iPP parts are analyzed using different experimental techniques (optical,small angle X-ray scattering and wide angle X-ray diffraction analysis).The results show that the thickness of the parts consist of five-layer skin-core morphology,e.g.frozen layer,transition layer,shear layer,β-phase crystallites layer andα-phase crystallites layer.The skin thickness(including frozen layer,transition layer and shear layer) decreases as the melt temperature increases from 210 ℃ to 250 ℃.The maximum degree of orientation does not change obviously.The crystallinity increases slightly with the melt temperature increasing.

    参考文献
    相似文献
    引证文献
引用本文

刘岩,王利霞,李倩,申长雨,贾振华.熔体温度对注塑成型iPP制品结晶形态的影响[J].高分子材料科学与工程,2012,28(7):79-82. Yan Liu, Lixia Wang, Qian Li, Changyu Sheng, Zhenhua Jia. Influence of Melt Temperature on the Morphology Evolution of Injection Molded Isotactic Polypropylene Parts[J]. Polymer Materials Science & Engineering,2012,28(7):79-82.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2013-04-16
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司