浸塑成型中冷却时间的优化
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

TQ320.66

基金项目:

安徽省自然科学基金资助项目(090414180);安徽高校省级自然科学研究重点项目(KJ2009A019);合肥工业大学创新实验项目(2010CXSY102177,2010CXSY102147)


Optimization of Cooling Time for Dip-Moulding
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    采用数学建模的方法对浸塑成型中制件的冷却过程进行了模拟。通过对浸塑件冷却过程中的传热作合理简化,建立传热过程的扩散方程,并由边界条件的齐次化等数学方法,推导出确定浸塑件冷却时间的计算方程。将方程应用于聚氯乙烯(PVC)浸塑件冷却时间的计算与确定,并对比经验公式做了讨论与分析。结果表明,通过公式计算确定的冷却时间可以减少生产中脱模困难的问题,降低制件的后收缩率,达到优化浸塑工艺和改善制件性能的目的。

    Abstract:

    An efficient numerical simulation was developed for the cooling process of dip moulding.The equation for heat diffusion in cooling process was established based on some rational simplification,and the equations for calculating the cooling time of dipping moulding were derived via mathematical way including homogenizing for non-homogeneous of boundary conditions and so on.Furthermore,this equation was applied to calculate the cooling time in the dip moulding process of polyvinyl chloride(PVC),and the values of cooling time were compared with the values calculated from the experience formula.The results show that the optimal cooling time could improve the products performance efficiently,demould easily,and reduce the after shrinkage ratio,so as to reach the purpose of optimization of dip-moulding.

    参考文献
    相似文献
    引证文献
引用本文

王中立,丁运生,方松喜,苏江林,杨绪峰.浸塑成型中冷却时间的优化[J].高分子材料科学与工程,2012,28(7):184-186,190. Zhongli Wang, Yunsheng Ding, Songxi Fang, Jianglin Su, Xufeng Yang. Optimization of Cooling Time for Dip-Moulding[J]. Polymer Materials Science & Engineering,2012,28(7):184-186,190.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2013-04-16
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司