异相后过渡金属聚乙烯的结构与性能
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

南昌航空大学科学基金(EA200601188)


Structure and Properties of Branched Polyethylene Prepared by Heterogeneous(α-Diimine) Nickel Catalyst
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    采用负载α-二亚胺镍配合物催化乙烯聚合制备不同支化度的聚乙烯(PE),应用核磁共振分析仪、差示扫描量热仪和广角X-射线衍射仪分析了异相后过渡金属催化剂制备的支化聚乙烯的支化结构与熔融行为、结晶行为及晶型特征。探讨支化度对PE熔融行为、结晶行为和晶型等的影响。随着支链度的提高,熔融温度和结晶温度都降低,熔融峰形变宽。当支链度为100.90时,降温曲线出现两个峰,衍射角在23°(2θ)附近,(200)晶面衍射峰消失,表明聚乙烯的型态为弹性态。

    Abstract:

    Polyethylene (PE) products with different degree of branching were prepared through ethylene polymerization catalyzed with heterogeneous α-diimine nickel complexes, and the effects of branching degree on melting behavior, crystal form of PE were investigated. The branching degrees were measured by 13C-NMR, melting points and crystal points of the products were measured by DSC. As the branching degree increases, the melting points and crystallization temperature of the products decrease, the melting points and crystallization temperature of the products decreases, the melting range becomes widened. Double peaks appear on DSC cooling curves as the branching degree reaches 100.90, and the diffraction peak of crystal surface(200) approximately at 23°(2θ) disappears, which indicates that PE becomes amorphous.

    参考文献
    相似文献
    引证文献
引用本文

江洪流,卢金山.异相后过渡金属聚乙烯的结构与性能[J].高分子材料科学与工程,2013,29(1):75-78. Hongliu Jiang, Jinshan Lu. Structure and Properties of Branched Polyethylene Prepared by Heterogeneous(α-Diimine) Nickel Catalyst[J]. Polymer Materials Science & Engineering,2013,29(1):75-78.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2013-09-23
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司