P(BA-co-Bd-co-St)-g-SAN/SAN 共混物的结构与性能
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:


Properties and Structure of Poly(Acrylate-co-Butadiene-co-Styrene)-g-SAN/SAN Blends
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    采用乳液聚合技术将丙烯酸丁酯(BA)和丁二烯(Bd)、苯乙烯(St)共聚制备P(BA-co-Bd-co-St)胶乳(简称丁苯酯),然后在丁苯酯乳胶粒子上接枝St和AN 合成P(BA-co-Bd-co-St)-g-SAN 接枝共聚物。将其与SAN 树脂熔融共混制备P(BA-co-Bd-co-St)-g-SAN/SAN共混物,研究了丁苯酯胶乳的粒径和组成对共混物力学性能和形态结构的影响。结果发现,引入丁二烯大大提高了SAN共聚物的接枝率,改善了共混物的冲击韧性,随着丁苯酯胶乳粒径的增加,共混物的冲击强度呈现先增大后减小的趋势。形态研究表明,丁二烯的引入显著改善了橡胶粒子在SAN 树脂中的分散状况,但当粒径较小时,橡胶粒子发生了聚集。

    Abstract:

    P(acrylate-co-butadiene-co-styrene(P(BA-co-Bd-co-St))) latex were prepared by emulsion polymerization. P(BA-co-Bd-co-St)-g-SAN copolymers were synthesized by grafting styrene(St) and acrylonitride(AN) on P(acrylate-co-butadiene-co-styrene) atex. Blends were prepared by blending these P(BA-co-Bd-co-St)-g-SAN grafting copolymers with SAN resins. The effects of P(BA-co-Bd-co-St) latex particle size and component on the properties and morphology of blend were investigated. It is found that the grafting degree of SAN copolymer is improved obviously by introducing PB, toughness is modified,the impact strength of blends increases and then decreases with increase of the P(BA-co-Bd-co-St) latex particle size, the impact strength of blend reaches the maximum value when the P(BA-co-Bd-co-St) latex particle size is 357.4nm. The morphology observation shows that the dispersion of rubber particles in SAN resins becomes better after the addition of PB, agglomeration of rubber particles occurs when the particle sizes is small because rubber particles cannot be completely covered by SAN copolymer.

    参考文献
    相似文献
    引证文献
引用本文

李立静,任 亮,李明远,张明耀,张会轩. P(BA-co-Bd-co-St)-g-SAN/SAN 共混物的结构与性能[J].高分子材料科学与工程,2013,29(2):46-49. Lijing Li, Liang Ren, Mingyuan Li, Mingyao Zhang, Huixuan Zhang. Properties and Structure of Poly(Acrylate-co-Butadiene-co-Styrene)-g-SAN/SAN Blends[J]. Polymer Materials Science & Engineering,2013,29(2):46-49.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2013-09-24
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司