可溶性PPESK/氰酸酯树脂体系的制备与性能
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

辽宁省高等学校优秀人才支持计划项目(RC-05-14);渭南师范学院研究生专项项目(12YKZ041)


Preparation and Characterization of PPESK/Cyanate Blends
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    采用热熔法制备了含氮杂萘聚醚砜酮(PPESK)/氰酸酯共混树脂体系。利用断裂韧性和弯曲实验考察了PPESK分子量对共混体系力学性能的影响规律,发现共混体系的临界应力强度因子(KIC)为1.00 MPa·m1/2~1.25 MPa·m1/2,弯曲强度和弯曲模量分别为140 MPa~148 MPa和3.26GPa~3.30GPa。使用热变形测试和热失重分析法(TGA)研究了体系的耐热性,共混体系的热变形温度约为266 ℃,在N2 气氛中5%热失重温度为415 ℃~428 ℃。对PPESK/氰酸酯树脂体系的介电性能测试结果表明,共混体系的介电常数和介电损耗角正切分别为3~3.2和0.006~0.007。

    Abstract:

    The poly (phthalazine ether sulfone ketone) (PPESK)/cyanate resin blends were prepared by the melt mixing method. The influence of PPESK molecular weight on the mechanical properties of the blends was investigated by the fracture toughness and the flexural testing. The critical stress intensity factor KIC of the blends is 1.00 MPa·m1/2~1.25 MPa·m1/2, while the flexural strength and flexural modulus are 140 MPa~148 MPa and 3.26 GPa~3.30 GPa respectively. The heat resistant properties of the blends were studied by the heat distortion test and thermogravimetric analysis (TGA). The heat distortion temperature and the temperature at 5% mass loss are 266 ℃ and 415 ℃~428 ℃, respectively. Finally, the results of the dielectric properties indicate that the dielectric constant and tanδare 3~3.2 and 0.006~0.007, respectively.

    参考文献
    相似文献
    引证文献
引用本文

李俊燕,陈 平.可溶性PPESK/氰酸酯树脂体系的制备与性能[J].高分子材料科学与工程,2013,29(2):149-151. Junyan Li, Ping Chen,. Preparation and Characterization of PPESK/Cyanate Blends[J]. Polymer Materials Science & Engineering,2013,29(2):149-151.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2013-09-24
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司