基于响应面法的异型腔模具顺序注塑成型工艺参数优化
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

中央高校基本科研业务费(CDJZR11130003)


Optimization of Parameters in Sequential Injecting Molding Process for Family Mold Using Response Surface Methodology
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    提出了基于响应面法(RSM)和有限元分析技术的顺序注塑成型(SIM)工艺参数优化方法,解决时序阀浇口设置对异型腔模具充填平衡性的影响。以阀浇口延时开启时间为设计变量,采用中心复合设计(CCD)进行试验规划,运用Moldflow有限元软件进行充填平衡性分析,并引入熵值权重法和线性加权和法对充填结束时间差和综合成型质量评价指标进行数值处理,基于有限元分析结果和响应面法构建了充填平衡性预测模型,应用构建的模型确定了最优工艺参数组合,并进行了数值模拟和生产试验验证。近似模型获得的目标预测值与模拟验证值相对误差为4.2%,优化后异型腔模具充填平衡性提高了23%,表明了所提出方法的有效性。

    Abstract:

    The aim of this work is to optimize the settings of sequential valve gates for filling balancing of family mold. The opening time of valve gates was considered as the main design variables. The central composite design (CCD) was employed in arranging the experimental points. The filling balancing performance analysis based on Moldflow software was conducted to acquire the objective variables for combination of process parameters. The entropy-based weight and linear weighted method were used to process the samples data of evaluation indicators such as filling time difference and quality. A predictive model for filling balancing performance was developed by using response surface methodology (RSM) exploiting finite element analysis results and the optimum parameters were obtained with the model. Also the validation was done by numerical imulation and production test. Predictive values compared to numerical filling test results show the reliability of the proposed model with the error of 4.2%, and filling balancing performance of multiple nonidentical cavity mold is improved by 23% after optimized.

    参考文献
    相似文献
    引证文献
引用本文

王梦寒,董晶晶,周 杰,邹 鹰,庄新如,姚小兵.基于响应面法的异型腔模具顺序注塑成型工艺参数优化[J].高分子材料科学与工程,2013,29(2):178-181. Menghan Wang, Jingjing Dong, Jie Zhou, Ying Zou, Xinru Zhuang, Xiaobing Yao. Optimization of Parameters in Sequential Injecting Molding Process for Family Mold Using Response Surface Methodology[J]. Polymer Materials Science & Engineering,2013,29(2):178-181.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2013-09-24
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司