Breath Figure法制备聚碳酸酯(PC)蜂窝状多孔膜
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(50973019);福建省自然科学基金资助项目(2010J06017);国家重点基础研究发展计划(973计划,2010CB732203)资助项目


Fabrication of Polycarbonate Honeycomb Porous Films by Breath Figure Method
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    以单组分聚碳酸酯(PC)为膜材质,在一定的湿度环境下,利用BreathFigure法在玻璃基板上成功制备了蜂窝状孔结构的聚碳酸酯多孔膜。研究了溶剂、溶液浓度和湿度对所成多孔膜结构和形貌的影响。实验结果表明,采用二氯甲烷为溶剂所制得的孔结构规整,排列均匀紧密,孔径大小为(3.30±0.19)μm,而以三氯甲烷为溶剂只能得到孔径大小不均且无紧密排列的孔。环境湿度从43%增加到91%,孔径大小由(2.28±0.63)μm 增加到(9.07±1.42)μm,且湿度与孔大小基本上呈现一阶线性关系,通过理论推导得出直线斜率为0.15μm/%,即在此体系中湿度每增加1%,所形成的孔大小增加0.15μm。

    Abstract:

    Well-ordered honeycomb structure of polycarbonate (PC) films was prepared via Breath Figure method on glass substrates in certain humidity atmosphere. The effects of factors, such as solvent, polymer concentration and relative humidity, on the pore patterns were investigated. The results show that regular honeycomb porous structure with pore size (3.30±0.19) μm is formed using CH2Cl2 with higher vapor pressure as solvent, but using CHCl3 the regular porous structure can't be got. The pore size of PC films increases from (2.28±0.63) μm to (9.07±1.42) μm with increasing relative humidity from 43% to 91%. The relationship of pore size and the relative humidity is presented first order liner relationship. Moreover, the slope of straight line is 0.15 μm/%, which indicates that with increasing of 1% relative humidity, the pore size increases by 0.15 μm in this system.

    参考文献
    相似文献
    引证文献
引用本文

刘瑞来,刘俊劭,刘海清. Breath Figure法制备聚碳酸酯(PC)蜂窝状多孔膜[J].高分子材料科学与工程,2013,29(3):133-136. Ruilai Liu, Junshao Liu, Haiqing Liu. Fabrication of Polycarbonate Honeycomb Porous Films by Breath Figure Method[J]. Polymer Materials Science & Engineering,2013,29(3):133-136.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2013-10-08
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司