溶胶-凝胶法制备紫外光固化聚氨酯丙烯酸酯/环氧丙烯酸酯/纳米二氧化硅杂化材料
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:


Preparation of UV-Curing Polyurethane Acrylate/Epoxy Acrylate/SiO2 Hybrid Materials by Sol-Gel Method
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    以正硅酸乙酯(TEOS)制备SiO2 溶胶,γ-甲基丙烯酰氧丙基三甲氧基硅烷(KH-570)为硅烷偶联剂,通过溶胶-凝胶法制备聚氨酯丙烯酸酯/环氧丙烯酸酯/二氧化硅杂化材料。采用场发射扫描电镜(FESEM)以及热失重方法进行分析。结果表明,TEOS与(PUA+EA)质量比为0.4∶1时,树脂中二氧化硅颗粒粒径最小,大约在80nm~100nm,分散均匀,当配比达到0.6∶1时,二氧化硅出现团聚现象。杂化材料热失重温度达到350℃,热分解温度为143.8℃,比纯树脂体系提高了将近1倍。

    Abstract:

    The polyurethane acrylate/epoxy acrylate/SiO2 hybrid materials were prepared by sol-gel method from 3-(trimethoxysilyl) propyl methacrylate (KH-570) and SiO2 sol produced by tetraethoxysilane (TEOS). The results of field emission scanning electron microscope (FESEM) indicate that the SiO2 particles are dispersed uniformly in resin matrix. The particles are the smallest with the mass ratios of TEOS∶(PUA+EA)=0.4∶1. And the diameter is approximately 80nm~100nm. when the ratios reach 0.6∶1, SiO2 particles are agglomerated. Meanwhile, the thermal analysis illuminates that the hybrid materials begin to lose mass at 350 ℃ and the initial decomposition temperature is 143.8 ℃, which is about twice than that of the pure resin with the mass ratios of TEOS∶(PUA+EA)=0.4∶1.

    参考文献
    相似文献
    引证文献
引用本文

杨泽惠,倪爱清,殷燕子,张红元,王继辉.溶胶-凝胶法制备紫外光固化聚氨酯丙烯酸酯/环氧丙烯酸酯/纳米二氧化硅杂化材料[J].高分子材料科学与工程,2013,29(4):121-124. Zehui Yang, Aiqing Ni, Yanzi Yin, Hongyuan Zhang, Jihui Wang. Preparation of UV-Curing Polyurethane Acrylate/Epoxy Acrylate/SiO2 Hybrid Materials by Sol-Gel Method[J]. Polymer Materials Science & Engineering,2013,29(4):121-124.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2013-10-08
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司