原子转移自由基聚合法在硅橡胶表面接枝聚甲基丙烯酸甲酯
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学青年基金资助项目(51203015);国家自然科学专项基金(51243003);青蓝工程;江苏省大学生实践创新基金(SCZ1214800035)


Polymethylmethacrylate Grafted onto Surfaces of Silicone Rubber via Atom Transfer Radical Polymerization
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    采用表面引发原子转移自由基聚合(SI-ATRP)在室温硫化硅橡胶表面接枝聚甲基丙烯酸甲酯(PMMA)。通过衰减全反射傅立叶变换红外光谱(FT-IR/ATR)、X射线光电子能谱(XPS)、接触角和扫描电子显微镜(SEM)对改性前后硅橡胶表面结构、表面形貌及表面润湿性进行表征。结果表明,在硅橡胶表面成功接枝了PMMA;随着聚合时间的延长,单位面积上的接枝量逐渐增大,当聚合时间为16h时,接枝量达到3.75mg/cm2;接触角从108.8°下降到71.7°;表面自由能从17.7mN/m 增大到32.0mN/m。

    Abstract:

    The surface of silicone rubber was modified via the grafting of polymethylmethacrylate (PMMA) by surface-initiated atom transfer radical polymerization(SI-ATRP). The surface composition and morphology of the modified silicone rubber were characterized by Fourier transform infrared spectroscopy (FT-IR), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and contact angle measurement. The results show that the surface of the silicone rubber is successfully grafted with PMMA. With the polymerization time expanding, the mass ner unit area increases. After 16h grafting reaction, the mass ner unit area is 3.75mg/cm2 and the water contact angle reduces from 108.8° to 71.7°, and the surface tension increases from 17.7 mN/m to 32.0 mN/m.

    参考文献
    相似文献
    引证文献
引用本文

史红岩,姜 彦,蔡 敏,张洪文,宋仁国,赵蒙超.原子转移自由基聚合法在硅橡胶表面接枝聚甲基丙烯酸甲酯[J].高分子材料科学与工程,2013,29(5):29-32. Hongyan Shi, Yan Jiang, Min Cai, Hongwen Zhang, Renguo Song, Mengchao Zhao. Polymethylmethacrylate Grafted onto Surfaces of Silicone Rubber via Atom Transfer Radical Polymerization[J]. Polymer Materials Science & Engineering,2013,29(5):29-32.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2013-10-08
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司