NaHCO3 协效发泡氯磺化聚乙烯橡胶微孔材料的结构与性能
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家科技部科研院所技术开发研究专项资金资助项目(2012EG111217)


Structure and Properties of NaHCO3 Synergistic Foaming Chlorosulfonated Polyethylene Rubber Microporous Materials
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    采用模压发泡技术,以NaHCO3 为协效发泡剂,制备了一系列兼具不同开闭孔形态的氯磺化聚乙烯橡胶(CSM)发泡材料。研究了NaHCO3 对发泡CSM 材料结构与性能的影响。结果表明,当NaHCO3 用量为8phr时,构成了吸放热平衡发泡体系,胶料硫化性能最好。SEM 显示,发泡材料均呈现两种尺寸水平并兼具开闭孔的微观结构。Nano-measure统计得出,随NaHCO3 用量增加,泡孔平均直径增大,孔壁变薄,开孔率提高,在保证泡孔不被气体胀破的前提下,用NaHCO3 来提高开孔率的有效用量为12phr;压缩应力应变曲线表明,CSM 泡沫具有典型弹性体发泡材料的特点,塌陷平台区的应力在NaHCO3 用量为12phr~24phr时几乎不变。

    Abstract:

    The effect of synergistic foaming agent NaHCO3 content on structure and properties of chlorosulfonated polyethylene rubber (CSM) foam with both open and closed-cell structure produced by compression molding technology was investigated. The results show that CSM materials form a thermal balanced foaming system between absorbing and releasing, and have the best vulcanizing properties when NaHCO3 loading is 8phr. SEM results show that the foams have two size-level microstructures with both open and closed-cells. With the increase of NaHCO3 content, the average cell diameter increases and the cell wall thickness decreases. The open cell percentage increases gradually with the increase of NaHCO3 content. On the premise that the cellular structure is not bursted, the effective dosage of NaHCO3 is 12phr to increase the open cell percentage. The compression stress-strain curves of CSM foams have typical characteristics of elastomer foams. The stress at plateau zone almost keeps unchanged when NaHCO3 content is between 12 phr and 24phr.

    参考文献
    相似文献
    引证文献
引用本文

冯 钠,王卫婷,常素芹,戚晓霞. NaHCO3 协效发泡氯磺化聚乙烯橡胶微孔材料的结构与性能[J].高分子材料科学与工程,2013,29(5):92-95. Na Feng, Weiting Wang, Suqin Chang, Xiaoxia Qi. Structure and Properties of NaHCO3 Synergistic Foaming Chlorosulfonated Polyethylene Rubber Microporous Materials[J]. Polymer Materials Science & Engineering,2013,29(5):92-95.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2013-10-08
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司