旋转/牵引速度比对旋转挤出聚乙烯管结构和性能的影响
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金科学仪器基础研究专项资助(51127003,51121001)


Effect of Rotating and Drawing Speeds on the Structure and Properties of Polyethylene Pipes Prepared by Rotation Extrusion
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    采用自行研制的聚合物管旋转挤出装置,研究了旋转挤出过程中旋转/牵引速度比对聚乙烯(PE)管结构和性能的影响。扫描电镜(SEM)和热收缩实验结果表明,通过控制旋转/牵引速度比,可有效调节PE管内串晶偏离轴向的角度,降低轴向取向度,提高PE管的力学性能。当旋转/牵引速度比为0.6时,旋转挤出PE管的环向拉伸强度从常规挤出管的19.4MPa提高到33.5MPa,提高了72.7%。

    Abstract:

    In this paper, a self-designed rotation extrusion system was adopted to extrude PE pipes, and the effects of rotating speed/drawing speed ratio on their structure and properties were investigated. The SEM photos and thermal shrinkage results show that by controlling the rotating speed/drawing speed ratio, the axial orientation degree that the shish-kebab crystals in PE pipe deviates from the axial direction is reduced and the hoop strength is improved. When the rotating speed/drawing speed ratio is 0.60, the hoop strength of the PE pipe reaches 33.5MPa from 19.4MPa, 72.7% higher than that of the conventionally prepared pipe.

    参考文献
    相似文献
    引证文献
引用本文

胡晓阳,聂 敏,白时兵,王 琪.旋转/牵引速度比对旋转挤出聚乙烯管结构和性能的影响[J].高分子材料科学与工程,2013,29(6):50-53. Xiaoyang Hu, Min Nie, Shibing Bai, Qi Wang. Effect of Rotating and Drawing Speeds on the Structure and Properties of Polyethylene Pipes Prepared by Rotation Extrusion[J]. Polymer Materials Science & Engineering,2013,29(6):50-53.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2013-10-08
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司