聚丙烯/尼龙6共混物熔体的松弛时间
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

常州大学校基金资助项目(ZMF07020038);国家社科基金项目(12BGL008)


Relaxation Time of Polypropylene/Polyamide 6 Blend Melts
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    用扫描电镜对聚丙烯(PP)/尼龙6(PA6)共混物断面形貌进行了表征,用旋转流变仪小振幅剪切模式测试了PP/PA6共混物的动态模量,并采用广义Maxwell模型对于损耗模量-角频率曲线进行了拟合。扫描电镜结果表明,聚丙烯接枝马来酸酐(PP-g-MAH)有效提高了PP和PA6之间的相容性,使得分散相PA6粒径尺寸减小。广义Maxwell模型中,当松弛模数为N=5和6时,拟合曲线与实验数据在低频下存在明显的偏差,而松弛模数为N =7时,广义Maxwell模型能够较好地拟合实验曲线。固定PP/PP-g-MAH 质量比为90/6时,随着PA6含量的增加,共混物PP/PP-g-MAH/PA6的松弛时间延长,松弛时间谱曲线以短时区为轴心逆时针旋转,向长时区偏移。

    Abstract:

    The structure morphology of cross-section of the polypropylene/polyamide 6 (PP/PA6) blends was characterized by scanning electron microscope (SEM). The dynamic modulus was measured by small amplitude oscillatory shear on rotationary rheometer, and the loss modulus-angular frequency data was fitted by the generalized Maxwell model. The SEM results show that polypropylene grafted maleic anhydride(PP-g-MAH)improves the compatibility between PP and PA6 phase. When the relaxation modulus N of the generalized Maxwell model is 5 or 6, obvious deviation exists between the fitted curve and the experimental loss moduli data at low angular frequency, but when N increases to 7, the model can fit the data well. When the weight content of PA6 phase increases with the fixed mass ratio PP/ PP-g-MAH of 90/6, the relaxation time of the PP/PP-g-MAH/PA6 blends increases, the relaxation modulus relaxation time curve rotates anticlockwisely to long time zone along the axis of short time zone.

    参考文献
    相似文献
    引证文献
引用本文

廖华勇,陶国良.聚丙烯/尼龙6共混物熔体的松弛时间[J].高分子材料科学与工程,2013,29(6):109-112. Huayong Liao, Guoliang Tao. Relaxation Time of Polypropylene/Polyamide 6 Blend Melts[J]. Polymer Materials Science & Engineering,2013,29(6):109-112.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2013-10-08
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司