低膨胀酚醛树脂(PF)/ZrW2O8 复合材料的制备与表征
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

河南省科技攻关项目


Preparation and Characterization of Low Thermal Expansion Phenolic Resin (PF)/ZrW2O8 Composites
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    采用固相反应法制备高纯立方相ZrW2O8 粉体,并用γ-氨丙基三乙氧基硅烷处理ZrW2O8,得到表面硅烷化的改性ZrW2O8。然后采用模压法制备酚醛树脂/ZrW2O8 和酚醛树脂/改性ZrW2O8 复合材料,探讨ZrW2O8 对复合材料热稳定性的影响,并考察断面填料的分散情况。结果表明,改性ZrW2O8 与酚醛树脂基体的相容性良好;少量改性ZrW2O8 提高了酚醛树脂/改性ZrW2O8 复合材料的起始热分解温度,添加量增大反而降低。热膨胀系数测试结果表明,ZrW2O8 的加入降低了复合材料的平均线膨胀系数,且改性ZrW2O8 对降低平均线膨胀系数的效果更明显。

    Abstract:

    Firstly, cubic ZrW2O8 with high purity was synthesized by solid state reaction. And functioned ZrW2O8 covered with (3-aminopropyl) siloxy group on the surface was obtained via modification using 3-aminopropyltriethoxysilane. Phenolic resin/ZrW2O8 and phenolic resin/modified ZrW2O8 composites were prepared by compression molding. The thermal stability of composites was analyzed, then the dispersion of ZrW2O8 in the fracture surfaces of composites was observed. The results show that modified ZrW2O8 has good compatibility with phenolic resin, and the addition of a small amount of modified ZrW2O8 improves the initial thermal decomposition temperature of the composites and then reduces as increase of fillers content. The test of coefficient of thermal expansion suggests that the fillers reduce the average coefficient of linear expansion of the composites significantly, especially the modified ZrW2O8 shows a better effect.

    参考文献
    相似文献
    引证文献
引用本文

刘雪莹,刘 莉,何素芹,刘文涛,朱诚身.低膨胀酚醛树脂(PF)/ZrW2O8 复合材料的制备与表征[J].高分子材料科学与工程,2013,29(6):133-136. Xueying Liu, Li Liu, Suqin He, Wentao Liu, Chengshen Zhu. Preparation and Characterization of Low Thermal Expansion Phenolic Resin (PF)/ZrW2O8 Composites[J]. Polymer Materials Science & Engineering,2013,29(6):133-136.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2013-10-08
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司