注水延迟时间对水辅共注成型充填的影响
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(51103037);江西省自然科学基金资助项目(2010GQC0029)


Influence of Water Injection Delay Time on Water-Assisted Co-Injection Molding Filling Process
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    基于流体力学三大控制方程和幂律粘性本构,针对水辅共注充填过程的特点,经合理假设与简化,建立了二维、瞬态、纯黏性、非等温的理论模型以及水辅共注填充过程中熔体相和水相的数学模型。采用有限体积法对整个水辅共注成型的填充过程进行模拟,研究注水延迟时间对熔体层和水层的分布影响。结果表明,随着注水延迟时间的延长,所需的注水压力增大,芯层熔体平均厚度增加,均匀度更好;同时水的穿透深度变大,宽度变小。

    Abstract:

    Based on the equations of fluid dynamics and power-law model, aimed at the characteristic of water-assisted co-injection molding filling process, two-dimensional, transient, viscous, non-isothermal theoretical model and mathematical model of melt phases and water phase in molding filling process were built up. The whole filling process was simulated by volume of fluid (VOF) method. The influence of water injection delay time on the distribution of melt phase and water phase was studied. The results show that, with water injection delay time increasing, the injection pressure and average thickness increase, thickness uniformity becomes better. At the same time, penetration length of water increases and penetration breadth decreases.

    参考文献
    相似文献
    引证文献
引用本文

章 凯,柳和生,匡唐清,曾效舒.注水延迟时间对水辅共注成型充填的影响[J].高分子材料科学与工程,2013,29(6):173-177. Kai Zhang, Hesheng Liu, Tangqing Kuang, Xiaoshu Zeng. Influence of Water Injection Delay Time on Water-Assisted Co-Injection Molding Filling Process[J]. Polymer Materials Science & Engineering,2013,29(6):173-177.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2013-10-08
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司