高密度聚乙烯共混物的抗冲击强度与熔体流动速率
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

常州大学校基金资助项目(ZMF07020038)


Impact Strength and Flow Melt Flow Rate of High Density Polyethylene Melts
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    制备了4种高密度聚乙烯(HDPE)HDPE8916/5000S、HDPE9641/5000S、HDPE5306/5000S和HDPE8916/6003T共混物,并测试其缺口冲击强度σin和熔体流动速率(MFR),探讨了两者之间的关系。结果表明,随着MFR的增加,缺口冲击强度逐渐下降,两者之间符合指数衰减规律。而其中HDPE5306/HDPE5000S的σin-MFR 曲线与坐标轴之间包围的面积最大,比其它3种共混物更容易实现同时满足冲击强度和流动性的要求。文中还对HDPE5306/HDPE5000S共混物用乙烯-辛烯共高聚物(POE)进行增韧改性。结果表明,当HDPE5306/HDPE5000S/POE的质量比为28.5/66.5/5时,缺口冲击强度达到42.88kJ/m2,高于HDPE5306/HDPE5000S(30/70,质量比,下同)时的28.16kJ/m2,而POE增韧后共混物的MFR为2.64g/10min(230℃,2.16kg),比HDPE5306/HDPE5000S(30/70)时的MFR值2.55g/10min(230℃,2.16kg)高。

    Abstract:

    Four high density polyethylene blends (HDPE 8916/5000S,HDPE 9641/5000S, HDPE 5306/5000S and HDPE 8916/6003T) were prepared. The notch impact strength σin and melt flow rate(MFR) were measured, and their relation was investigated. The results show that the notch impact strength σin drops with the increase of MFR, the σin-MFR curve meets the law of exponential decay. The area of σin-MFR curve surrounded by coordinate axes is the highest for HDPE 5306/HDPE5000S blend, which suggests it is the easiest for HDPE 5306/HDPE5000S blend to meet the notch impact strength and MFR requirement. Then HDPE 5306/HDPE5000S blend was toughened by adding polyolefin elastomer (POE). The results show when the mass ratio of HDPE 5306/ HDPE5000S/POE is 28.5/66.5/5, the notch impact strength σin arrives 4288 kJ/m2 and the MFR is 2.64 g/10min(230℃,2.16kg), much higher than of HDPE 5306/HDPE5000S( 30/70, mass ratio, similarly hereinafter), 28.16 kJ/m2 and 2.55 g/10min(230℃,2.16kg), respectively.

    参考文献
    相似文献
    引证文献
引用本文

廖华勇,陶国良.高密度聚乙烯共混物的抗冲击强度与熔体流动速率[J].高分子材料科学与工程,2013,29(7):72-75. Huayong Liao, Guoliang Tao. Impact Strength and Flow Melt Flow Rate of High Density Polyethylene Melts[J]. Polymer Materials Science & Engineering,2013,29(7):72-75.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2013-10-08
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司