分型面为曲面的套类注射制品的有限元分析
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(50974107);徐州市科技计划资助项目(XC12A013);江苏师范大学自然科学基金资助项目(10XLS01)


Finite Element Analysis of Sleeve-Shape Injection Molding Products with Streamlined Parting Surface
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    根据塑件开口端的特殊形状,为了让推件板与曲面端吻合,推件板的形状依照塑件顶端的曲边而设计成曲面。运用Moldflow有限元软件,在模具制造之前,通过CAE软件的分析结果选择合理的成型工艺条件和冷却方法。结果表明,CAE与Pro/E的有机结合,可以预测可能产生熔接痕、气穴等缺陷的位置,避免了传统方法的反复试模、修模所引起的成本上升。从根本上提高了设计的准确性和高效性,大大缩短了设计周期。

    Abstract:

    For sleeve-shape injection molding products with streamlined open end, large numbers of rejects would come out if using conventional designing methods. Stripper plate was designed according to the special shape of open end, so that stripper plate and plastic part surface can anastomose with each other. Before manufacturing the injection mold, reasonable process parameters and cooling method can be obtained by applying Moldflow and the analysis of the CAE software. The results show that the combination of Pro/E and CAE is helpful to predict the possible position of weld lines and air traps, avoid high cost caused by repeated mold testing and mold repairing. In essence, the designing accuracy and efficiency are increased, and mold designing cycle is tremendously shortened.

    参考文献
    相似文献
    引证文献
引用本文

范希营, 郭永环, 李顺才.分型面为曲面的套类注射制品的有限元分析[J].高分子材料科学与工程,2013,29(7):170-174. Xiying Fan, Yonghuan Guo, Shuncai Li. Finite Element Analysis of Sleeve-Shape Injection Molding Products with Streamlined Parting Surface[J]. Polymer Materials Science & Engineering,2013,29(7):170-174.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2013-10-08
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司