乙烯-乙烯醇共聚物微图案膜的制备与表征
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(50973038,21006070,51173132);天津市应用基础及前沿技术研究计划重点项目(11JCZDJC23700,11JCZDJC21200);高等学校博士学科专项科研基金(20111201110003,20091201120002)


Preparation and Characterization of Ethylene-co-Vinyl Alcohol Copolymer Micro-Patterned Membranes
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    通过模板复制法制备具有微米级图案的乙烯-乙烯醇共聚物(EVAL)微图案膜。采用电子显微镜等表征方法,研究影响EVAL微图案膜结构性能的因素与微图案复制性的关系,考察微图案对膜材料浸润性的影响。研究表明,微图案增大膜表面的粗糙度,显著改善了EVAL膜的浸润性。当凝固浴温度为30℃时,EVAL柱形微图案膜表面的接触角为23.1°,与EVAL原膜相比,接触角降低10°左右。研究发现较低的相分离速率有利于EVAL微图案膜的复制;微图案复制规整度越高,图案收缩率越有利于微图案的复制。

    Abstract:

    Ethylene-co-vinyl alcohol copolymer (EVAL) micro-patterned membranes were prepared by template copying method. The effect of surface micro-pattern on wettability of membrane surfaces was investigated by FE-SEM. The influence of membrane morphological structure on the performance of micro-pattern was also studied. The results show that the micro-patterns on EVAL membrane surface can improve the wettability of EVAL membrane. The contact angle of EVAL micro-pillar membrane is 23.1° when the coagulation bath temperature is 30 ℃, which is 10° lower than that of original EVAL membrane. The slow phase separation is in favor of micro-patterned replication. When the shrinkage of micro-pattern decreases and the regulation of micro-patterned replication increases, the wettability of EVAL membrane surface improves. The increasing of polymer concentration and ethylene content of EVAL, and the decreasing of coagulation bath temperature are advantage to increase the regulation of micro-patterned replication.

    参考文献
    相似文献
    引证文献
引用本文

侯 琴, 张玉忠, 林立刚, 丁晓莉, 叶 卉, 李 泓.乙烯-乙烯醇共聚物微图案膜的制备与表征[J].高分子材料科学与工程,2013,29(8):169-173. Qin Hou, Yuzhong Zhang, Ligang Lin, Xiaoli Ding, Hui Ye, Hong Li. Preparation and Characterization of Ethylene-co-Vinyl Alcohol Copolymer Micro-Patterned Membranes[J]. Polymer Materials Science & Engineering,2013,29(8):169-173.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2013-10-24
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司