两步溶解法制备纤维素/[BMIM]Cl体系的再生纤维素纤维
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(50903015,50873024);863计划项目(2009AA03Z425)


Cellulose Fibers Regenerated from Cellulose/[BMIM]Cl Spinning Dope Through Two-Steps Dissolving Process
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    以离子液体1-丁基-3-甲基咪唑氯盐([BMIM]Cl)为溶剂,采用间接溶解法(即先在含水[BMIM]Cl中溶胀后再减压蒸馏去除多余的水使之溶解)制备了纤维素/[BMIM]Cl纺丝液,通过干湿法纺丝制得再生纤维素纤维。探讨了纺丝速度对纤维的结构与性能的影响,研究了纤维的热稳定性及表观形态。结果表明,随着纺丝速度的提高,喷头拉伸比增大,纤维素大分子取向度和结晶度提高,聚集态结构更加完善,纤维的平均微孔孔径逐渐减小,纤维的力学性能相应提高。此外,再生纤维素纤维具有较好的热稳定性及光洁的表面形态。

    Abstract:

    Ionic liquid 1-butyl-3-methylimidazolium chloride ([BMIM]Cl) used as the solvent of cellulose, the cellulose spinning dope was prepared by two-steps dissolving process, i.e. cellulose was firstly swelled to the maximum in aqueous [BMIM]Cl solution and then dissolved by stirring under vacuum to remove excessive water. The cellulose fibers were spun by the dry-jet wet spinning process. The effects of the spinning speed on the structure and properties of cellulose fibers were investigated, and then the thermal stability and surface morphology of fibers were discussed. The results show that with the increasing of spinning speed, the degree of orientation and crystallinity of cellulose fibers increases and the average micropore diameter of fibers decreases, and then the mechanical properties of cellulose fibers are improved. The regenerated cellulose fibers show a good thermal stability and the surface morphology is smooth.

    参考文献
    相似文献
    引证文献
引用本文

张慧慧, 蔡 涛, 杨革生, 邵惠丽, 胡学超.两步溶解法制备纤维素/[BMIM]Cl体系的再生纤维素纤维[J].高分子材料科学与工程,2013,29(8):178-181. Huihui Zhang, Tao Cai, Gesheng Yang, Huili Shao, Xuechao Hu. Cellulose Fibers Regenerated from Cellulose/[BMIM]Cl Spinning Dope Through Two-Steps Dissolving Process[J]. Polymer Materials Science & Engineering,2013,29(8):178-181.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2013-10-24
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司