微结构塑件注塑成型的复制度分析
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家高技术研究发展项目(863计划,2012AA040406);辽宁省自然科学基金资助项目(201202036)


Analysis of the Replication Fidelity of Injection Molding for Microstructure Plastic Part
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    以典型微结构塑件———微流控芯片为研究对象,对芯片纵、横微通道的复制度进行比较、分析。发现在注塑成型过程中,由于熔体与型腔微凸起之间的作用关系不同,导致芯片纵、横微通道的复制度存在明显差异,且横向微通道两侧的开口形状也不一致;基于熔体充模流动基本理论,建立了用来描述横向微通道开口圆角大小的数学表达式;利用新型电热式变模温注塑成型系统,对上述分析结果加以实验验证。结果表明,实测横向微通道开口圆角大小与计算结果基本一致。

    Abstract:

    The replication fidelities of longitudinal and transverse micro-channels for microfluidic chip(the typical microstructure plastic part) were analyzed. Because of the interaction relationship difference between melt and micro-convexity of cavity, it was found that significant difference exists between them, and the opening shape of both sides of transverse micro-channel is also inconsistent. Based on the melt filling flow theory, the mathematical expression which can describe the opening round size of transverse micro-channel was built. Using the new electric variotherm system, the results show that the measured opening round size of transverse micro-channel is agreement with the calculated one.

    参考文献
    相似文献
    引证文献
引用本文

宋满仓, 熊林城, 连城林, 刘冲, 杜立群.微结构塑件注塑成型的复制度分析[J].高分子材料科学与工程,2013,29(8):182-185. Mancang Song, Lincheng Xiong, Chenglin Lian, Chong Liu, Liqun Du. Analysis of the Replication Fidelity of Injection Molding for Microstructure Plastic Part[J]. Polymer Materials Science & Engineering,2013,29(8):182-185.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2013-10-24
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司