无机填料对封端聚氨酯/环氧树脂共混物涂料力学和表面性能的影响
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:


Influence of Inorganic Fillers on Mechanical and Surface Properties of Blocked Polyurethane/Epoxy Resin Blend Coatings
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    研究了无机填料对新型封端聚氨酯(BPU)/环氧树脂(EP)共混物涂料的拉伸强度、剪切强度和表面性能的影响。拉伸实验结果表明,涂层的拉伸强度随填料用量的增加而升高,但当用量大于15phr后,基本上不再增加,并且氧化锌的效果优于二氧化硅;剪切强度测试结果表明,涂层与钢板的剪切强度随二氧化硅用量的增加而下降,而随氧化锌用量的增加先降低,然后逐步恢复到无填料的水平以上;接触角测试结果表明,二氧化硅填料可使涂层与水的接触角增加,疏水性增强,而氧化锌则对涂层的疏水性增加不明显。

    Abstract:

    The influence of inorganic fillers on the tensile strength, shear strength and surface properties of blocked polyurethane/epoxy resin blend coatings was investigated. The results of tension tests show that the tensile strength of the coatings increases as the filler amount increases. When the filler amount is over 15phr, the tensile strength doesn’t obviously increase. Enhancing effect of zinc oxide on the film is better than that of silica. The shear strength between the coatings and steel is reduced with SiO2 amount increasing, first reduced and then enhanced with ZnO amount increasing. The results of contact angle measurements indicate that silicon dioxide can obviously enhance the hydrophobicity of the coatings, but zinc oxide can’t enhance the hydrophobicity.

    参考文献
    相似文献
    引证文献
引用本文

张 梦,晏 欣,刘明光,王 俊.无机填料对封端聚氨酯/环氧树脂共混物涂料力学和表面性能的影响[J].高分子材料科学与工程,2013,29(9):110-113. Meng Zhang, Xin Yan, Mingguang Liu, Jun Wang. Influence of Inorganic Fillers on Mechanical and Surface Properties of Blocked Polyurethane/Epoxy Resin Blend Coatings[J]. Polymer Materials Science & Engineering,2013,29(9):110-113.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2013-11-11
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司