功能性核/壳结构共聚物乳液的制备及共混改性聚对苯二甲酸丁二醇酯
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(51073049,21001039)


Preparation of Functionalized Core-Shell Poly(BA/MMA-co-MAA) and Its Application in Toughening PBT
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    采用氧化还原引发体系、种子乳液聚合方法制备了功能单体甲基丙烯酸甲酯(MMA)含量不同的核壳结构共聚物(Poly(BA/MMA-co-MAA),PBMMA)乳液。单体总转化率达99.6%,乳胶粒径(dz)在421nm 左右,粒径多分散指数(PDI)均小于0.08,表明胶束无二次成核过程;透射电镜(TEM)观察到PBMMA明显的核壳结构。当MAA质量分数为0.9%时,PBT/PBMMA(质量比100/20)共混物的缺口冲击强度达到最大值,为纯PBT 的7.6 倍。动态力学分析(DMA)结果表明,橡胶相的内耗峰向高温方向移动,聚对苯二甲酸丁二醇酯(PBT)的内耗峰向低温方向移动,力学损耗峰变宽,且当MAA的质量分数为0.9%时,两峰间的差值最小,说明此时的PBMMA 与PBT 间相容性最好。扫描电镜(SEM)观察到的共混物冲击断面证实了力学性能的变化。

    Abstract:

    A series of core-shell poly(BA/MMA-co-MAA) (PBMMA) latex with different amounts of functional monomer methacrylic acid( MAA) were produced with redox initiator system by seed emulsion polymerization. The overall conversion of the monomers reaches up to 99.6% and almost all the instantaneous conversion is over 96%. The latex particle size (dz) is 421 nm and the polydispersity index (PDI) is less than 0.08. The experimental values of particle sizes are in accordance with calculated ones, indicating that the particles have grown without significant secondary nucleation. When 0.9% functional monomer (MAA) was used, the Charpy notched impact strength of PBT/PBMMA (mass ratio of 100/20) reaches the maximum, increases to 7.6 times of that of pure PBT resin. DMA spectra show that the internal friction peak of the rubber phase moves to high temperature and the internal friction peak of PBT to low temperature, the mechanical loss peak becomes wider. These results show that the compatibility of PBMMA particles with PBT matrix is the best when 0.9% functional monomer was used. SEM observation confirms the mechanical results.

    参考文献
    相似文献
    引证文献
引用本文

付 念,李国华,秦丽丽,杨运燕,张立群,瞿雄伟.功能性核/壳结构共聚物乳液的制备及共混改性聚对苯二甲酸丁二醇酯[J].高分子材料科学与工程,2013,29(9):132-135. Nian Fu, Guohua Li, Lili Qin, Yunyan Yang, Liqun Zhang, Xiongwei Qu. Preparation of Functionalized Core-Shell Poly(BA/MMA-co-MAA) and Its Application in Toughening PBT[J]. Polymer Materials Science & Engineering,2013,29(9):132-135.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2013-11-11
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司