PTT/TPEE共混合金的流变学及成型温度对韧性的影响
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

河北省自然科学基金资助项目(B2010000219)


Rheology and Influences of Molding Temperatures on the Impact Strength of PTT/TPEE Blends
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    采用毛细管流变仪、冲击试验机、差示扫描量热仪(DSC)和广角X射线衍射仪(WAXD)研究了聚对苯二甲酸丙二醇酯(PTT)/热塑性聚酯弹性体(TPEE)共混合金的流变性能和成型温度对冲击强度的影响。结果表明,共混物的表观黏度和假塑性随着TPEE含量的增加而提高,TPEE 对PTT 具有较好的增粘效果,有利于改善PTT 的加工性能;且TPEE对PTT还具有良好的增韧效果,但共混材料的韧性随着成型温度的升高而降低,主要是由于在较高的成型温度下共混材料的结晶度较高,高结晶度的样条具有较低的韧性。

    Abstract:

    In order to toughen poly(trimethylene terephthalate)(PTT) material, thermoplastic polyester elastomer (TPEE) was blended with PTT to prepare PTT/TPEE blends. Their rheology behaviors, impact strength dependence on molding temperatures were investigated by capillary rheometer, impact tester, wide angle X-ray diffraction (WAXD) and differential scanning calorimetry (DSC), respectively. The results suggest that the apparent viscosities and the pseudoplasticity of PTT/TPEE blends increase with increasing TPEE contents, and TPEE has good effect on improving the processing viscosity of PTT. TPEE also has good toughening effect on the blend materials but the toughness decreases with increasing molding temperatures from 25 ℃ to 75 ℃ due to the increase of their crystallinity.

    参考文献
    相似文献
    引证文献
引用本文

白玉清,闰明涛,王 建,刘迎宾,李 刚. PTT/TPEE共混合金的流变学及成型温度对韧性的影响[J].高分子材料科学与工程,2013,29(10):60-63. Yuqing Bai, Mingtao Run, Jian Wang, Yingbin Liu, Gang Li. Rheology and Influences of Molding Temperatures on the Impact Strength of PTT/TPEE Blends[J]. Polymer Materials Science & Engineering,2013,29(10):60-63.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2013-11-11
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司