L-丙交酯-乙交酯-ε-己内酯共聚物模压工艺的正交设计
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家“十二五”科技支撑计划课题(2012BAI31B06)


Orthogonal Experiment of Poly(L-Lactide-co-Glycolide-co-ε-Caprolactone) Compression Moulding
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    以L-丙交酯、乙交酯和ε-己内酯为原料开环聚合合成三元共聚物PLLGC。通过正交试验设计研究了预热温度、模压压力、模压温度、模压时间等因素对PLLGC模压材料性能的影响,确定了PLLGC材料最佳的模压工艺。研究了不同因素对PLLGC模压材料的拉伸强度、密度、模压后分子量及分子量分布的影响,通过极差分析结果表明,PLLGC三元共聚物的最佳模压工艺条件:预热温度为150℃,模压压力为8MPa,模压温度为100℃,模压时间为10min。

    Abstract:

    Poly(L-lactide-co-glycolide-co-ε-caprolactone) (PLLGC) was synthesized by ring-opening polymerization using L-lactide, glycolide and ε-caprolactone. The influences of compression moulding parameters such as preheating temperature, moulding pressure, mould temperature and moulding time on the properties of PLLGC were researched by orthogonal experiment to determine the optimal processing parameters. The influences of the processing parameters on the tensile strength, density, molecular weight and molecular weight distribution of PLLGC after compression moulding were researched by range analysis. The results show that the optimum compression moulding parameters of PLLGC are as follows: preheating temperature of 150 ℃, moulding pressure of 8 MPa, mold temperature of 100 ℃, and molding time of 10 min.

    参考文献
    相似文献
    引证文献
引用本文

朱爱臣,王 勤,王传栋,刘 阳,杜 旭,马丽霞. L-丙交酯-乙交酯-ε-己内酯共聚物模压工艺的正交设计[J].高分子材料科学与工程,2013,29(10):105-108. Aichen Zhu, Qin Wang, Chuandong Wang, Yang Liu, Xu Du, Lixia Ma. Orthogonal Experiment of Poly(L-Lactide-co-Glycolide-co-ε-Caprolactone) Compression Moulding[J]. Polymer Materials Science & Engineering,2013,29(10):105-108.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2013-11-11
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司