动态硫化氢化丁腈橡胶/三元共聚尼龙热塑性弹性体的制备与性能
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:


Preparation and Mechanical Properties of Dynamically Vulcanized Hydrogenated Nitrile Rubber/Ternary Copolymerization Nylon Blends
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    以氢化丁腈橡胶(HNBR)与三元共聚尼龙(PA)进行共混,制备了动态硫化热塑性弹性体(TPV)。研究了不同硫化体系的硫化特性,发现硫磺硫化体系交联程度低,过氧化二异丙苯(DCP)硫化体系交联程度高;并考察了DCP体系下不同PA含量、加工温度以及返炼次数对TPV性能的影响,观察了其微观结构。结果表明,加工温度170 ℃最佳;返炼使拉伸强度下降;随着PA含量的增加拉伸强度增加;扫描电镜(SEM)显示其形态为两相结构,分散相HNBR是以微米级颗粒分散在PA连续相中,随着PA含量增加,分散相HNBR颗粒分布更均匀,颗粒尺寸明显变小,大小介于0.5μm~1μm。

    Abstract:

    A thermoplastic vulcanizate of hydrogenated nitrile rubber and ternary copolymerization nylon with excellent mechanical properties was prepared by dynamic vulcanization. Different vulcanization characteristic curves show that the crosslinking degree of sulfur vulcanization system is low while of the dicumyl peroxide (DCP) vulcanization system is high. The effect of polyamide (PA) contents, processing temperature and reprocessing times on thermoplastic vulcanizate (TPV) was investigated. The results show that the best processing temperature is 170 ℃ and tensile strength decreases after reprocessing, meanwhile, the tensile strength increases with increasing PA content. The morphology images observed by (SEM) show the form of two phase structure, and the dispersed phase of hydrogenated nitrile rubber (HNBR) is micron particles dispersed in the continuous phase of PA. The distribution of HNBR particles becomes more uniform with the increase of PA content, and the particle size decreases significantly which is between 0.5μm and 1μm.

    参考文献
    相似文献
    引证文献
引用本文

刘 欣,郑 威,赵丽芬,周彩华,姜 虎,梁 雷.动态硫化氢化丁腈橡胶/三元共聚尼龙热塑性弹性体的制备与性能[J].高分子材料科学与工程,2013,29(10):155-159. Xin Liu, Wei Zheng, Lifen Zhao, Caihua Zhou, Hu Jiang, Lei Liang. Preparation and Mechanical Properties of Dynamically Vulcanized Hydrogenated Nitrile Rubber/Ternary Copolymerization Nylon Blends[J]. Polymer Materials Science & Engineering,2013,29(10):155-159.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2013-11-11
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司