基于响应面法的酚醛树脂固化条件优化
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(30972311);福建省科技厅产学研重大专项基金资助项目(2010N5001);福建省林业厅科学基金资助项目(闽林科201103-2)


Curing Condition Optimization of Phenol-Formaldehyde Resin by Response Surface Methodology
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    为促进酚醛树脂固化、降低能耗,采用响应面法对影响酚醛树脂固化的3个主要因素:固化剂用量、热压温度、热压时间进行优化。以胶合强度为考察指标,在单因素试验的基础上,根据中心复合设计原理进行试验设计,并对各因素及其相互之间的交互作用进行分析。结果表明,影响树脂固化因数的顺序为热压温度>热压时间>固化剂用量。当固化剂质量为胶液量的 1.35%,热压温度105 ℃,热压时间0.8 min/mm时,制得的Ⅰ类胶合板胶合强度为1.21 MPa,达到国家标准GB9846-2004的要求(≥0.8 MPa)。

    Abstract:

    In order to promote the curing and reduce the energy consumption of phenol-formaldehyde resin during the curing process, the curing factors, such as curing agent usage, hot pressing temperature, and hot pressing time, were optimized through the response surface methodology. Using bonding strength as response index, the response surface methodology experiment according to Central- Composite Design was carried out after the single-factors tests, then curing factors and its interactions were investigated as well. The results show that the order of effects in the curing process is as follow: hot pressing temperature>hot pressing time>curing agent usage. Bonding strength of plywood is 1.21 MPa which meets the requirements (0.80 MPa) of the China National Standard (GB/T9846-2004 plywood type I) when the mass of curing agent usage is 1.35% of the phenol-formaldehyde resin, hot pressing temperature is 105 ℃, and hot pressing time is 0.8 min/mm.

    参考文献
    相似文献
    引证文献
引用本文

黄剑峰, 陈奶荣, 林巧佳, 饶久平, 曾钦志.基于响应面法的酚醛树脂固化条件优化[J].高分子材料科学与工程,2013,29(11):92-96. Jianfeng Huang, Nairong Chen, Qiaojia Lin, Jiuping Rao, Qinzhi Zeng. Curing Condition Optimization of Phenol-Formaldehyde Resin by Response Surface Methodology[J]. Polymer Materials Science & Engineering,2013,29(11):92-96.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2013-11-11
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司