异向双螺杆废旧胶粉脱硫挤出过程中的动力计算及分析
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家高技术研究发展计划项目(863)(2012AA063005)


Modeling on the Dynamic Analysis of the Rubber Devulcanization in the Counter-Rotating Twin Screw Extruder
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    以异向双螺杆脱硫挤出固态再生胶过程为研究对象,提出了一种用于计算螺杆扭矩和功耗的方法。首先,针对螺杆单个C形室内的物料进行功耗、扭矩的建模。然后设计了一套粉体松密度-压力测试装置,得到了胶粉的松密度-压力关系曲线。综合考虑压力因素对粉体松密度和摩擦系数的影响,得到了整段螺杆上的压力分布,完成了螺杆的功耗、扭矩计算。通过实验对比,预测值和实测值之间的最大误差为10.4%,验证了此功耗、扭矩计算方法的合理性。

    Abstract:

    On the basis of the rubber devulcanization in a counter-rotating twin screw extruder, an experimental method to predict the torque and power of the extruder was proposed in this paper. Firstly, the modeling of torque and power for the rubber particles in a single C-chamber of the counter-rotating twin screw extruder was built. Then a bulk density-pressure measurement device for powder was designed and the relationship between the bulk density and the pressure of rubber particles was considered by this device. Finally, the value of power and torque and the pressure distribution along the screw were calculated using the model and combining the factors of pressure, bulk density and friction coefficient. Compared with the experimental results, the error of the predicted value is below 10.4% and the computational models are reasonable.

    参考文献
    相似文献
    引证文献
引用本文

张有军, 任冬云, 张立群, 史金炜, 胡学永, 林 祥.异向双螺杆废旧胶粉脱硫挤出过程中的动力计算及分析[J].高分子材料科学与工程,2013,29(11):168-172. Youjun Zhang, Dongyun Ren, Liqun Zhang, Jinwei Shi, Xueyong Hu, Xiang Lin. Modeling on the Dynamic Analysis of the Rubber Devulcanization in the Counter-Rotating Twin Screw Extruder[J]. Polymer Materials Science & Engineering,2013,29(11):168-172.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2013-11-11
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司