介孔分子筛/丙烯酸钠改性三元乙丙吸水膨胀橡胶的合成及性能
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(51103086,51173110);辽宁省高等学校杰出青年学者成长计划(LJQ2011040);中国博士后自然科学基金资助项目(2012M510922)


Water-Swelling Properties of EPDM Rubber Modified by in Situ Formed Sodium Acrylate/Mesoporous Molecular Sieve
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    通过氢氧化钠(NaOH)与丙烯酸(AA)的中和反应,在三元乙丙橡胶(EPDM)中原位合成丙烯酸钠(NaAA),同时在橡胶中加入介孔分子筛MCM-41进行机械混炼,并在有机过氧化物作用下将所得混炼胶进行硫化,研究不同配比的丙烯酸钠与介孔分子筛MCM-41对吸水膨胀橡胶的影响。研究结果表明,随着MCM-41用量的增加,吸水膨胀橡胶(WSR)的拉伸强度、断裂伸长率、吸水膨胀率均得到提高。尤其是加入MCM-41(0.5phr)时拉伸强度、断裂伸长率、吸水膨胀率均达到最大值,分别为6.4MPa、386.2%、210%,比未添加MCM-41组分的橡胶的拉伸强度提高了18%,断裂伸长率提高了16.8%,吸水膨胀率提高了13.5%。通过扫描电镜看出,加入MCM-41(0.5phr)的样品与未添加分子筛之前样品相比,其骨架呈立体网状结构,孔洞均匀。表明MCM-41的加入起到了增容剂和协效剂作用。

    Abstract:

    A water-swelling rubber was prepared using sodium acrylate (NaAA) in situ formed in EPDM rubber. Mesoporous molecular sieve MCM-41 was added into rubber, and obtained blends were vulcanized with dicumyl peroxide (DCP). The effect of the content of sodium acrylate and MCM-41 on the mechanical properties of the water-swelling rubber were investigated. The results show that the tensile strength, elongation at break, and water-swelling properties reach the maximum value of 6.4MPa,386.2%,210% respectively when the content of MCM-41 is 0.5 phr, and increase by 18%, 16.8%, 13.5% respectively comparing with those of rubber without MCM-41. SEM images show that the skeleton of the water-swelling rubber with 0.5 phr MCM-41 is a three-dimensional network and the structure of holes is homogeneous, implying that MCM-41 together with NaAA can be used as a compatibilizer to increase the miscibility.

    参考文献
    相似文献
    引证文献
引用本文

王 娜,孙 冰,张 静,李旭日,方庆红.介孔分子筛/丙烯酸钠改性三元乙丙吸水膨胀橡胶的合成及性能[J].高分子材料科学与工程,2013,29(12):13-17. Na Wang, Bing Sun, Jing Zhang, Xuri Li, Qinghong Fang. Water-Swelling Properties of EPDM Rubber Modified by in Situ Formed Sodium Acrylate/Mesoporous Molecular Sieve[J]. Polymer Materials Science & Engineering,2013,29(12):13-17.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2013-12-06
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司