β成核剂复配改性聚丙烯的力学性能与熔融行为
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:


Mechanical Properties and Melting Behavior of Polypropylene Modified with Complex of β Nucleating Agents
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    选用酰胺类和稀土类β成核剂进行复配,对均聚聚丙烯(PPH)进行改性。采用偏光显微镜(PLM)、X 射线衍射(XRD)、差示扫描量热法(DSC)等手段,对改性PPH 的结晶微观结构、熔融行为及力学性能进行了研究。结果表明,两类β成核剂复配改性PPH 后,其缺口冲击强度远超过同剂量单一类型的β成核剂的效果,达到了纯PPH 的4.6倍左右,两者具有明显的协同效应;同时PPH 的刚性也得到了较好地保持。PLM 观测显示,复配体系改性PPH 的晶型呈“雪花”状生长,有别于同温度下任一单体系。XRD测试结果表明,复配体系中β晶相对含量介于两单一体系之间,PPH中β晶相对含量与其韧性并不是简单的直线关系。DSC二次熔融曲线表明,改性PPH 中以β晶占主体地位,复配后PPH 的β晶熔融峰向低温方向移动。

    Abstract:

    Homo-polypropylene (PPH) was modified with a mixture of amides and rare β nucleating agents, and the microstructure and mechanical properties of modified PPH were studied. It is found that the notched impact strength of PPH modified with a complex of β nucleating agents exceeds that with any single β nucleating agent at the same dose, and reaches approximately 4.6 times of that of pure PPH. The synergistic toughening effect is obvious, while the rigidity is maintained. The crystalline form of the compound system is “snowflake-like” distinguished from that of any single system at a particular temperature as observed through polarized light microscopy (PLM). X-ray diffraction (XRD) curves indicate that relative content of β-crystal of PPH is between the two single ones′. Second melting curves of differential scanning calorimeter (DSC) show that the β-crystalline form in a dominant position among the overall crystallization; compared with the β-peak position in a single nucleating system, the position moves towards the low temperature.

    参考文献
    相似文献
    引证文献
引用本文

李景宜,梁 馨,郑 德,郭丽媛,李冬静,丁会利.β成核剂复配改性聚丙烯的力学性能与熔融行为[J].高分子材料科学与工程,2013,29(12):52-56. Jingyi Li, Xin Liang, De Zheng, Liyuan Guo, Dongjing Li, Huili Ding. Mechanical Properties and Melting Behavior of Polypropylene Modified with Complex of β Nucleating Agents[J]. Polymer Materials Science & Engineering,2013,29(12):52-56.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2013-12-06
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司