环氧型丙烯酸酯橡胶增韧聚乳酸的结构与性能
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(51273025,50803007)


Structure and Property of Epoxy-Functionalized Acrylic Rubber Toughened Polylactide
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    采用甲基丙烯酸环氧丙酯与丙烯酸酯类单体共聚的环氧型丙烯酸酯橡胶(ACM)增韧聚乳酸(PLA)。冲击测试结果发现,随着ACM 含量的增加,共混物冲击强度先增加后降低,增韧剂最佳的质量分数为25%,冲击强度可达到670J/m;拉伸性能测试表明,随着ACM 含量增加,共混物的杨氏模量和屈服应力逐渐降低;ACM 的玻璃化转变温度随着橡胶组分的增加逐渐上升,PLA相的玻璃化转变温度变化不明显;差示扫描量热(DSC)测得加入ACM 后,PLA 冷结晶温度降低;扫描电镜(SEM)发现橡胶粒子质量分数为10%时能均匀分散在PLA 中,ACM 含量增加,相区尺寸变大;形变区观察发现,ACM 橡胶粒子发生空洞化,基体发生剪切屈服。

    Abstract:

    The copolymer of glycidyl methacrylate and acrylate monomer (ACM) was used to toughen polylactide (PLA). The impact test result indicates that the impact strength of the blends increases first and then decreases with the ACM content increasing. When the mass faction of ACM is 25%, the impact strength reaches the maximum value of 670J/m. The tensile test shows that the Young’s modulus and yielding stress of the blends decrease with the ACM content increasing. The glass transition temperature (Tg) of ACM increases with the ACM content and Tg of PLA changes little. DSC test indicates the cold crystallization temperature of PLA decreases with the addition of ACM. SEM shows that ACM disperses in the PLA matrix uniformly when the mass fraction of ACM is 10%, and the phase domain size increases with the ACM content increasing. Deformation zone observed by SEM shows that the cavitation takes place for ACM and the shear yielding occurs for the PLA matrix.

    参考文献
    相似文献
    引证文献
引用本文

何 亮,孙树林,张明耀,张会轩.环氧型丙烯酸酯橡胶增韧聚乳酸的结构与性能[J].高分子材料科学与工程,2013,29(12):82-85. Liang He, Shulin Sun, Mingyao Zhang, Huixuan Zhang. Structure and Property of Epoxy-Functionalized Acrylic Rubber Toughened Polylactide[J]. Polymer Materials Science & Engineering,2013,29(12):82-85.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2013-12-06
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司