聚己内酯接枝甲基丙烯酸缩水甘油酯的制备及对聚己内酯/淀粉的增容作用
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

福建省自然科学基金重点项目(2012N0027);国家自然科学基金资助项目(50973019)


Compatibilizing Effect of Polycaprolactone Grafted with Glycidyl Methacrylate on Polycaprolactone /Starch Blends
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    以过氧化苯甲酰(BPO)为引发剂,甲基丙烯酸缩水甘油酯(GMA)为反应单体,通过熔融接枝反应将GMA 接枝到聚己内酯(PCL)上,制备了PCL-g-GMA。以PCL-g-GMA为增容剂,制备了PCL/淀粉/PCL-g-GMA共混物。扫描电镜表明,PCL/淀粉共混物界面粘接力差、淀粉出现团聚。然而加入PCL-g-GMA 后,PCL/淀粉/PCL-g-GMA 中淀粉分散变得均匀,且淀粉颗粒被PCL包裹,两相界面更加模糊。拉伸实验表明,加入PCL-g-GMA 增容剂后,共混物的拉伸强度由(12.3±2.1)MPa增加到(17.0±3.2)MPa,拉伸模量由(4.2±1.8)GPa增加到(5.7±2.9)GPa.断裂伸长率由(210±16)% 增加到(803±40)%。

    Abstract:

    Polycaprolactone-graft-glycidyl methacrylate (PCL-g-GMA) copolymer was prepared by grafting GMA onto PCL using benzoyl peroxide (BPO) as an initiator. PCL/starch blends were prepared by using PCL-g-GMA copolymer as a compatibilizer. SEM results show that the interfacial adhesion of PCL/starch blends without the PCL-g-GMA copolymer is poor and the starch granules are clearly observed. The starch granules are better dispersed and covered with PCL when the PCL-g-GMA copolymer was added as a compatibilizer. Compared with PCL/starch blends, the mechanical properties of PCL/starch/PCL-g-GMA blends are obviously increased, such as tensile strength at break increasing from (12.3±2.1) MPa to (17.0±3.2) MPa, tensile modulus from (4.2±1.8) GPa to (5.7±2.9) GPa and elongation at break from (210±16)% to (803±40)%.

    参考文献
    相似文献
    引证文献
引用本文

穆寄林,赵升云.聚己内酯接枝甲基丙烯酸缩水甘油酯的制备及对聚己内酯/淀粉的增容作用[J].高分子材料科学与工程,2013,29(12):168-171. Jilin Mu, Shengyu Zhao. Compatibilizing Effect of Polycaprolactone Grafted with Glycidyl Methacrylate on Polycaprolactone /Starch Blends[J]. Polymer Materials Science & Engineering,2013,29(12):168-171.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2013-12-06
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司