非等温粘弹性熔体挤出成型过程的形态及性能
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

上海市教育委员会科研创新重点项目(12ZZ066);高等学校博士学科点专项科研基金(10W10324);中央高校基本科研业务费资助项目;教育部创新团队发展计划


Extrusion Process Morphology and Performance of Non-Isothermal Viscoelastic Melt
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    对粘弹性流体,非均匀的径向温度所造成的不均匀的径向应力,使熔体在挤出过程中产生非均匀结晶和纤维微观结构的改变。采用PTT模型,通过POLYFLOW 软件模拟PA6熔体从圆形喷丝微孔中挤出的流动行为,分析熔体在不同的卷绕速度下沿纺程的拉伸速率分布、温度分布及结晶度的变化情况。结果表明,沿纺程纤维中心和纤维表面的速度几乎重合,在纤维横向断面上拉伸速率是均匀的,而且卷绕速度越低,拉伸速率越容易达到稳定;沿纺程纤维中心温度要高于纤维表面温度,且卷绕速度对纺程上的温度影响不大。研究结论对实际纤维产品和纺丝生产工艺有较好的参考作用。

    Abstract:

    For viscoelastic fluid, the non-uniform radial stress caused by non-uniform radial temperature made the non-uniform crystallization and the change of fiber microstructure for viscoelastic melt. Using PTT viscoelastic constitutive equation, the flow behavior of PA6 melt was simulated by POLYFLOW software. The stretching rate distribution, temperature distribution and crystallinity of PA6 melt along the spinning path with different winding speeds were analyzed. The simulation results show that the speeds of fiber center and fiber surface are almost coincident. The stretching rate is uniform in the fiber cross-section, and the low winding speed is conducive to the convergence of stretching rate. Fiber center temperature is higher than the fiber surface temperature, and winding speed has a little effect on the temperature. These results provide a theoretical basis for the polymer melt spinning.

    参考文献
    相似文献
    引证文献
引用本文

王 磊,陈 淮,马晓建,杨崇倡,甘学辉.非等温粘弹性熔体挤出成型过程的形态及性能[J].高分子材料科学与工程,2014,30(1):44-47. Lei Wang, Huai Chen, Xiaojian Ma, Chongchang Yang, Xuehui Gan. Extrusion Process Morphology and Performance of Non-Isothermal Viscoelastic Melt[J]. Polymer Materials Science & Engineering,2014,30(1):44-47.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2014-01-07
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司