轮胎胎面胶料共挤出过程的数值模拟
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

江苏省自然基金资助项目项目(BK2011405);江苏省高校自然科学研究面上项目(12KJB430006);江苏省普通高校研究生科研创新计划项目(CXZZ12_0666)


Numerical Simulation of Tread Rubber Coextrusion Process
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    以某复合胎面胶料(TWR/FB)的共挤出过程为研究对象,利用Polyflow 软件,采用Phan-ThienandTanner(PTT)本构模型和Navier滑移模型对2种胶料熔体在口模内外的流动进行了三维数值模拟,并将模拟得到的挤出断面和试验挤出断面进行了对比分析。同时分析了牵引速度和预口型板的收敛角对共挤出的影响,结果表明,牵引速度对胶料离开口模后的形状和面积胀大比的影响显著,但对胶料在口模内部的流动状态影响不大;适当地增加预口型板收敛角可以增强胶料在口模内的流动性,提高挤出制品的质量。

    Abstract:

    Taking the coextrusion process of tread rubber (TWR/FB) as study object, the three-dimensional flow of the viscoelastic melt at the exit for the coextrusion process of tread rubber was simulated by Phan-Thien and Tanner(PTT) constitutive equation and Navier slip equation, the simulated and actual cross section were compared. The effect of drawing velocity and convergence angle on coextrusion process was simulated. The result show that the drawing velocity obviously affects the shape and swell ratio of tread rubber after leaving the die, but has little effect on the flow condition in the die. Improving the convergence angle of the pre-die plate can enhance the rubber flow condition in the die, then it is necessary to design an appropriate convergence angle to get high quality products.

    参考文献
    相似文献
    引证文献
引用本文

梁 晨,刘高君,姜 波,王国林,李国瑞.轮胎胎面胶料共挤出过程的数值模拟[J].高分子材料科学与工程,2014,30(1):100-103. Chen Liang, Gaojun Liu, Bo Jiang, Guolin Wang, Guorui Li. Numerical Simulation of Tread Rubber Coextrusion Process[J]. Polymer Materials Science & Engineering,2014,30(1):100-103.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2014-01-07
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司