聚乙二醇增塑醋酸纤维素中空纤维膜的制备与性能
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

973计划(2012CB722706);中国纺织工业联合会应用基础研究项目资助


Preparation and Properties of PEG Plastified Cellulose Acetate Hollow Fiber Membranes
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    以聚乙二醇为增塑剂,采用熔融纺丝-拉伸法制备了具有海绵状孔结构的二醋酸纤维素(CA)中空纤维均质膜。通过场发射扫面电子显微镜、纯水通量、泡点孔径、孔隙率及力学性能测试讨论了成孔剂含量和拉伸条件对CA 中空纤维膜结构和性能的影响。结果表明,随拉伸倍数和成孔剂含量提高,膜内外表面孔径均增大,孔隙率提高,通透性改善。随成孔剂含量提高,中空纤维膜断裂强度和断裂伸长率均降低;随拉伸倍数提高,中空纤维膜断裂强度提高而断裂伸长率降低。当成孔剂含量为55%,拉伸倍数为2.25时,所得膜性能较好,膜纯水通量为186.44L/(m2·h),断裂强度为5.47MPa,断裂伸长率为5.30%。

    Abstract:

    Cellulose acetate hollow fiber membranes were prepared via melt-spinning/cold-stretching method using polyethylene glycol (PEG) as plasticizer. The effects of pore creating agent content and stretching on morphologies, permeability and mechanical properties were observed by field emission scanning electron microscope (FESEM) and analyzed by measurements of bubble point pore size, porosity, pure water flux, and mechanical strength. The results show that the hollow fiber membrane is a kind of homogeneous membrane with sponge-like pore structure. The membrane surface pore size, porosity and permeability increase with the increase of the pore creating agent content and draw ratio. With the increase of pore creating agent content, the tensile strength and elongation at break decrease. With the increase of draw ratio, the tensile strength increases and the elongation at break decreases. As the pore creating agent content and draw ratio reach 55% and 2.25, respectively, the pure water flux is 186.44 L/(m2·h), tensile strength is 5.47 MPa and elongation at break is 5.30%.

    参考文献
    相似文献
    引证文献
引用本文

王 恒,肖长发,刘海亮,黄庆林.聚乙二醇增塑醋酸纤维素中空纤维膜的制备与性能[J].高分子材料科学与工程,2014,30(1):122-126. Heng Wang, Changfa Xiao, Hailiang Liu, Qinglin Huang. Preparation and Properties of PEG Plastified Cellulose Acetate Hollow Fiber Membranes[J]. Polymer Materials Science & Engineering,2014,30(1):122-126.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2014-01-07
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司