熔体mLLDPE静电纺纤维基锂电池隔膜的制备
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:


Preparation of Lithium Battery Separator Based on Melt-Electrospun mLLDPE Fibers
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    采用熔体静电纺丝方法制备了茂金属线性低密度聚乙烯(mLLDPE)无纺纤维,并与聚偏氟乙烯(PVDF)溶液静电纺纳米纤维复合改性,成功制备出mLLDPE无纺纤维基锂电池隔膜。对该锂电池隔膜的孔隙率、热稳定性、充放电性能测试结果表明,该隔膜的孔隙率在54%~62%,首次放电比容量为70mA·h/g,且循环稳定性良好,性能优于同等测试条件下的商业锂电池隔膜,可以应用于锂电池。

    Abstract:

    mLLDPE non-woven fibers were successfully prepared via melt electrospinning. However, the fibers are thick, and the pores size of membrane made from mLLDPE non-woven fibers is large, so mLLDPE non-woven fibers cannot be directly used as lithium battery separator. Electrospun PVDF nanofibers and the melt-electrospun mLLDPE fibers were combined to form a new compounding membrane, which was successfully applied as lithium battery separator. The porosity rate, thermal stability and charge and discharge properties were characterized. The results show that the porosity rate of the composite separator is 54%~62% and the first specific discharge capacity is 70 mA·h/g with a good cyclic performance. The performance of this compounding membrane is superior to the commercial lithium separator under the same test condition.

    参考文献
    相似文献
    引证文献
引用本文

马福瑞,刘太奇,赵 娜.熔体mLLDPE静电纺纤维基锂电池隔膜的制备[J].高分子材料科学与工程,2014,30(1):153-156. Furui Ma, Taiqi Liu, Na Zhao. Preparation of Lithium Battery Separator Based on Melt-Electrospun mLLDPE Fibers[J]. Polymer Materials Science & Engineering,2014,30(1):153-156.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2014-01-07
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司