脂肪族聚醚酯热塑性弹性体的合成与性能
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(50873071,51003066)


Synthesis and Properties of Biodegradable Aliphatic Poly(Ether-Ester)s Thermoplastic Elastomers
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    本文合成了以聚丁二酸丁二醇酯(PBS)为硬段,聚四氢呋喃醚(PTMO,相对分子质量1000)为软段的生物降解脂肪族聚醚酯热塑性弹性体,其中PTMO 的质量分数为50%、60%、70%。采用核磁共振氢谱、差示扫描量热法、凝胶渗透色谱、力学性能测试对嵌段共聚物的结构、熔融行为、力学性能进行了表征。结果表明:合成的目标产物为PBS/PTMO嵌段共聚物;Mn 和Mw 分别达到5.0×104 和13.0×104 以上;软段PTMO 的结晶温度(Tc)较低,分别为-17.9 ℃、-14℃和-17.4℃;而硬段的Tc 较高,分别为54.6 ℃和46.3 ℃;合成的嵌段共聚物表现出热塑性弹性体的力学行为,拉伸强度分别为22MPa、18MPa和14MPa;弹性恢复率性能测试表明合成的脂肪族聚醚酯热塑性弹性体具有较好的弹性恢复性能。

    Abstract:

    The aliphatic poly(ether-ester)s thermoplastic elastomers based on poly(butylene succinate) (PBS) as hard segment and poly(tetramethylene oxide) (PTMO, Mn=1000) as soft segment were synthesized. The mass fraction of soft PTMO segments in the polymer chains is 50%, 60% and 70%. The copolymers were characterized by 1H nuclear magnetic resonance spectrum (1H-NMR), permeation chromatography (GPC), differential scanning calorimetry (DSC) and mechanical test. Mn and Mw of the poly(ether-ester)s are higher than 5.0×104 and 13.0×104 respectively. Crystallization temperature (Tc) of PTMO soft blocks is -17.9 ℃,-14 ℃ and -17.4 ℃; however, that of PBS is 54.6 ℃ and 46.3 ℃. The deformation behavior of the synthesized poly(ether-ester)s shows the characteristics of thermoplastic elastomers. Stress at break of PBSPTMO50, PBSPTMO60 and PBSPTMO70 is approximately 22 MPa, 18 MPa and 14 MPa respectively. Elongation at break of all three samples reaches above 700%. The recovery rates tests show that the aliphatic poly(ether-ester)s thermoplastic elastomers have good recovery properties.

    参考文献
    相似文献
    引证文献
引用本文

黄 勇,周 涛,张爱民.脂肪族聚醚酯热塑性弹性体的合成与性能[J].高分子材料科学与工程,2014,30(2):105-109. Yong Huang, Tao Zhou, Aimin Zhang. Synthesis and Properties of Biodegradable Aliphatic Poly(Ether-Ester)s Thermoplastic Elastomers[J]. Polymer Materials Science & Engineering,2014,30(2):105-109.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2014-02-11
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司