泡沫冻胶调剖体系的优选及性能评价
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家“十二五”科技重大专项(2011ZX05014-006)


Optimization and Evaluation of the Foamed Gel as Profiling Control Agent
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    优选了泡沫冻胶调驱体系,研究了聚合物、交联剂的用量及温度、pH 值、矿化度对泡沫冻胶体系的影响。结果表明,泡沫冻胶体系的组成为0.2%(质量分数,下同)、相对分子质量2000万的部分水解聚丙烯酰胺,0.15%~0.2%交联剂,0.2%表面活性剂发泡剂。在60℃、pH=7、矿化度6000mg/L条件下,泡沫冻胶体系的黏度达到最大值,成胶强度最大;当黏度达到最大值之前,泡沫冻胶的黏度随着温度的升高、pH 和矿化度的增加而增大;当黏度超过最大值后,泡沫冻胶的黏度随着温度的升高、pH 和矿化度的增加逐渐降低。

    Abstract:

    The influence of concentration of polymer and crosslinking agent, temperature, salinity on the breakthrough vacuum and gel strength of foamed gel was discussed. The foamed gel used as profile control agent was composed of 0.2% polyacrylamide based polymer compound(P-2000), 0.15%~0.2% crosslink agent NJ-8 and 0.2% surfactant foaming agent. The results show that the viscosity of foamed gel reaches the maximum value peak at 60 ℃, with pH of 7 and salinity of 6000 mg/L. The viscosity of foamed gel increases with the increase of temperature, pH and salinity, and after the viscosity of foamed gel reaches the maximum value, it decreases with the increase of temperature, pH and salinity.

    参考文献
    相似文献
    引证文献
引用本文

张 烨,王彦玲,金家锋,杨胜来.泡沫冻胶调剖体系的优选及性能评价[J].高分子材料科学与工程,2014,30(3):109-112. Ye Zhang, Yanling Wang, Jiafeng Jin, Shenglai Yang. Optimization and Evaluation of the Foamed Gel as Profiling Control Agent[J]. Polymer Materials Science & Engineering,2014,30(3):109-112.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2014-03-17
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司