T型口模气辅挤出段长度对挤出物截面形状和挤出胀大的影响
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

中山市科技计划项目资助(20114A260)


Influence of the Slip Length of T-Shape Gas-Assisted Extrusion on the Die Swell and the Warping of Extrudate
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    采用数值模拟的方法对T型截面口模气辅挤出成型过程中滑移段长度、挤出流量和松弛时间对挤出物的变形和挤出胀大的影响进行了研究。结果表明,气辅挤出段长度的增加可以减小挤出物的变形和挤出胀大,减小挤出流量和松弛时间对变形和挤出胀大的影响,并且当气辅挤出段的长度增加到一定值后,挤出胀大比为1且不受松弛时间和挤出流量的影响,这个值随挤出流量的增加和松弛时间的延长而增加。

    Abstract:

    The influence of the slip length, flow rate and relaxation time on the die swell and warping in the gas assisted extrusion of T-shape plastic profile was investigated by the numerical simulation. The results show that with the increase of gas-assisted extrusion length, the warping and die swell of the extrudate are reduced, and comparatively the influence of flow rate and relaxation time on that is also reduced. When the length of gas-assisted extrusion increases to a certain value, the die swell ratio approaches to 1 and does not be influenced by flow rate and relaxation time, but the length of gas-assisted extrusion increases with the increasing of flow rate and relaxation time.

    参考文献
    相似文献
    引证文献
引用本文

宋建辉,黄兴元. T型口模气辅挤出段长度对挤出物截面形状和挤出胀大的影响[J].高分子材料科学与工程,2014,30(3):139-143. Jianhui Song, Xingyuan Huang. Influence of the Slip Length of T-Shape Gas-Assisted Extrusion on the Die Swell and the Warping of Extrudate[J]. Polymer Materials Science & Engineering,2014,30(3):139-143.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2014-03-17
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司