前驱体对水性PU/SiO2复合材料结构与耐水性能的影响
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

四川省科技支撑计划项目(2012FZ0013)


Influence of Precursors on the Structure and Water Resistance of Waterborne PU/Silica Composites
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    在阴离子水性聚氨酯分散体(WPU)存在下,通过前驱体正硅酸乙酯(TEOS)和甲基三乙氧基硅烷(MTES)的共水解缩合反应,在m(前驱体)/m(WPU)为1时制备出WPU/SiO2(WPUS)复合材料。研究了n(MTES)/n(TEOS)对WPUS复合乳液平均粒径及粒子形貌、膜表面形貌及耐水性能的影响。结果表明,随着n(MTES)/n(TEOS)由0增大到1.5,复合乳液平均粒径由130nm 逐渐减小为107nm;没有加入MTES的乳液中SiO2 粒子以无规则形态非均匀分布,而加入MTES后乳液中SiO2 为均匀分布的规则球形;随n(MTES)/n(TEOS)增大,复合膜表面SiO2 分布均匀度逐渐提高,表面粗糙度逐渐减小,同时膜的水接触角逐渐增大,吸水率逐渐下降。

    Abstract:

    Waterborne PU/silica (WPUS) composites were synthesized by the co-hydrolysis and condensation of tetraethoxysilane (TEOS) and methyltriethoxysilane (MTES) at m(precursors)/m(WPU) of 1.0 in the presence of anionic waterborne PU dispersion. Influence of n(MTES)/n(TEOS) on the average particle size of WPUS composite emulsion, morphology of emulsion particles, surface morphology and water resistance of composite films was investigated by particle size analyzer, transmission electron microscopy, scanning probe microscopy, contact angle measuring device and water absorption test, respectively. With increasing of n(MTES)/n(TEOS) from 0 to 1.5, average particle size of emulsion decreases gradually from 130 nm to 107 nm; the distribution of silica on the surface of films becomes more uniformly and surface roughness decreases; water contact angle increases and water absorption decreases. Silica particles with irregular shape are distributed non-uniformly without addition of MTES, whereas they are distributed uniformly with regular sphere shape after addition of MTES.

    参考文献
    相似文献
    引证文献
引用本文

樊武厚,李正军,但年华,黄 金.前驱体对水性PU/SiO2复合材料结构与耐水性能的影响[J].高分子材料科学与工程,2014,30(4):70-74. Wuhou Fan, Zhengjun Li, Nianhua Dan, Jin Huang. Influence of Precursors on the Structure and Water Resistance of Waterborne PU/Silica Composites[J]. Polymer Materials Science & Engineering,2014,30(4):70-74.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2014-04-18
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司