聚乙烯醇/聚乙烯吡咯烷酮共混材料的热塑加工性能
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

科技部国家国际科技合作专项项目(2013DFG52300,2010DFA54460)


Thermal Processability of Polyvinyl Alcohol / Polyvinyl Pyrrolidone Blends
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    通过热塑加工方法制备了聚乙烯醇/聚乙烯吡咯烷酮(PVA/PVP)共混材料,采用差示扫描量热分析、热重分析、傅里叶红外光谱、高压毛细管流变仪等研究了PVA 与PVP间的氢键作用、共混材料的热行为和流变性能。结果表明,PVP可与PVA及改性剂形成氢键复合,增加体系氢键类型,能进一步屏蔽PVA 羟基,延缓其脱除反应,提高其初始热分解温度,有利于PVA的热塑加工。随PVP含量增加,共混体系熔融温度先略升高,后降低,获得86.4 ℃热塑加工窗口;熔体表观黏度和剪切敏感性均先增大后减小,PVP质量分数为20%时达最大;而粘流活化能降低,表明共混体系对温度的敏感性降低,PVA加工稳定性提高。适量PVP可促进PVA 的结晶,提高材料拉伸强度;PVP质量分数为10%时,材料拉伸强度最大,为43MPa。

    Abstract:

    Polyvinyl alcohol/polyvinyl pyrrolidone (PVA/PVP) blends were difficult to be thermal processed due to their special structure and properties. In this paper, by adopting molecular complexation and plasticization, PVA/PVP blends were prepared through thermal processing. By means of DSC, TGA, FTIR and high pressure capillary rheometer, the intermolecular interactions, thermal behavior and rheological property of the blends were studied. The results show that PVP can form hydrogen bonding with PVA and modifiers, thus increased the hydrogen bonding types of the systems, and further shielded the hydroxyl groups in PVA molecular chains and retarded their dehydroxylation, resulting in increase of the initial decomposition temperature, which is beneficial to the thermal processing of PVA. With increase of the PVP content, the melting temperature of the systems slightly increases and then decreases, obtaining the thermal processing window of 86.4 ℃; both the apparent viscosity and the shear sensitivity of the melt increase first and then decrease after the mass fraction of PVP reaches 20%; and the flow activation energy is reduced, indicating the improvement of the stability of the thermal processing of PVA. The addition of proper PVP, i.e. 10%, can increase the crystallinity of PVA, thus obtained the highest tensile strength, i.e. 43MPa.

    参考文献
    相似文献
    引证文献
引用本文

王金月,王 佳,李 莉.聚乙烯醇/聚乙烯吡咯烷酮共混材料的热塑加工性能[J].高分子材料科学与工程,2014,30(4):80-84. Jinyue Wang, Jia Wang, Li Li. Thermal Processability of Polyvinyl Alcohol / Polyvinyl Pyrrolidone Blends[J]. Polymer Materials Science & Engineering,2014,30(4):80-84.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2014-04-18
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司