聚丙烯挤出发泡材料的泡孔结构
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(31270610);湖北省自然科学基金资助项目(2009CDB136)


Cellular Structure of Polypropylene Foam During Extrusion Foaming Process
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    利用旋转流变仪、单螺杆挤机、扫描电镜等考察了高熔体强度聚丙烯(HMSPP)流变性能,研究了温度及机头压力对泡孔形态的影响。结果表明,通过接枝交联可以制备HMSPP;在冷却过程中,梯度温度分布导致泡孔尺寸沿棒材中心到边缘呈梯度分布;机头压力对泡孔形态影响较大,当机头压力从9.6MPa上升到13.6MPa时,泡孔密度从9.46×105cm-3上升到1.11×108cm-3,泡孔直径从91μm 下降到29μm,当机头压力从11.9MPa下降到7.1MPa时,泡孔密度从2.35×107cm-3降低到5.15×106cm-3,泡孔直径从51μm 升高到123μm。此外,较低的机头压力导致泡孔呈双峰分布。

    Abstract:

    The rheological properties of high melt strength propylene (HMSPP) were studied by rotary rheometer. Influences of temperature and head pressure on cell morphology were investigated by single screw extruder and scanning electron microscope. The results show that HMSPP was obtained by chemical grafting and cross-linking reaction. The cell sizes of the foams show a gradient distribution from the center region to the rim of the strand due to the gradient temperature field during curing process. The head pressure has significant impact on the cellular morphology. The cell density increases from 9.46×105cm-3 to 1.11×108cm-3 and cell size decreases from 91 μm to 29 μm when the head pressure improves from 9.6 MPa to 13.6 MPa. While, the cell density decreases from 2.35×107cm-3 to 5.15×106cm-3 and cell size increases from 51μm to 123 μm when the head pressure decreases from 11.9 MPa to 7.1 MPa. The low head pressure leads to cell size a bi-modal distribution.

    参考文献
    相似文献
    引证文献
引用本文

胡圣飞,朱贤兵,刘清亭,胡 伟,蔡 畅,晏 翎.聚丙烯挤出发泡材料的泡孔结构[J].高分子材料科学与工程,2014,30(4):90-94. Shengfei Hu, Xianbing Zhu, Qingting Liu, Wei Hu, Chang Cai, Ling Yan. Cellular Structure of Polypropylene Foam During Extrusion Foaming Process[J]. Polymer Materials Science & Engineering,2014,30(4):90-94.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2014-04-18
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司