三元乙丙橡胶的环氧官能化及增韧尼龙6
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:


Toughening of Nylon-6 with Epoxy-Functionalized Ethylene-Propylene-Diene Rubber
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    采用熔融接枝的方法在三元乙丙橡胶(EPDM)上接枝甲基丙烯酸环氧丙酯(GMA)得到EPDM-g-GMA。采用红外光谱证实GMA成功接枝到EPDM 分子链上。将环氧官能化的EPDM 与尼龙6熔融共混,对共混体系的相形态及力学性能进行了研究。结果表明,通过接枝反应在EPDM 中引入GMA,改善了EPDM 与PA6之间的相容性,分散相的尺寸从15μm 减小到1μm,共混物的冲击强度从原来的70J/m 左右提高到600J/m 以上,共混物的冲击强度显著提高,同时共混物的拉伸强度也得到提高。

    Abstract:

    Ethylene-propylene-diene rubber(EPDM) were grafted with glycidyl methacrylate (GMA) by reactive blending to prepare EPDM-g-GMA. The grafting reaction was confirmed by FT-IR spectra. Epoxy-functionalized EPDM blended with PA6. Morphology and mechanical properties of PA6/ EPDM-g-GMA blends were investigated in detail. The results show that the compatibility between PA6 and EPDM is improved with the introduction of GMA. The size of dispersed phase obviously decreases from 15 μm to 1 μm with the introduction of EPDM or EPDM-g-GMA. The Izod notched impact strength of blends dramatically improves from about 70 J/m to more than 600 J/m, and the tensile strength of the blends is improved simultaneously.

    参考文献
    相似文献
    引证文献
引用本文

谭志勇,崔秀丽,刘世纯.三元乙丙橡胶的环氧官能化及增韧尼龙6[J].高分子材料科学与工程,2014,30(4):171-175. Zhiyong Tan, Xiuli Cui, Shichun Liu. Toughening of Nylon-6 with Epoxy-Functionalized Ethylene-Propylene-Diene Rubber[J]. Polymer Materials Science & Engineering,2014,30(4):171-175.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2014-04-18
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司