双螺杆挤出法连续化制备聚乙交酯及性能表征
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

江苏省高校自然科学研究重大项目(11KJA430007)


Characterization of Properties of Polyglycolide Continuously Prepared by Twin Screw Extruder
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    以氯化亚锡为催化剂,利用双螺杆挤出法使乙交酯快速开环聚合连续制备高相对分子质量的聚乙交酯(PGA)。研究了不同催化剂含量、螺杆转速和反应温度对聚合物相对分子质量的影响,通过正交试验得出最佳反应工艺:反应温度227℃,催化剂与单体质量比为0.28∶1000,螺杆转速20r/min,所合成的聚乙交酯特性黏度可达0.89dL/g。通过加入不同配比的复合抗氧剂可调节PGA的颜色。利用凝胶渗透色谱、X射线衍射、差示扫描量热、热重分析和CMT系列微机控制电子拉力试验机等手段表征了聚合物的结构,测试了其热学和力学性能。结果表明,该法所制得的PGA 结晶度达58.4%,其熔融温度在222.48℃~223.48℃之间,最高弹性模量达到1430.19MPa,最高拉伸强度达130.51MPa。

    Abstract:

    Polyglycolide (PGA) with high molecular weight was rapidly and continuously synthesized from glycolide by using stannous chlorides as catalyst in the reactor of twin-screw extruder. The effects of different catalyst content, reaction temperature and screw speed on polymer properties were investigated. Through orthogonal test, the optimum reaction conditions of polymerization by twin screw extruder was obtained, the reaction temperature 227 ℃, the mass ratio of monomer to catalyst 0.28∶1000, the screw speed 20r/min and the intrinsic viscosity of PGA reaches 0.89 dL/g. By adding different proportions of antioxidant, samples with different shades were obtained. Different PGA was characterized and tested by gel permeation chromatography (GPC), differential scanning calorimetry (DSC), thermo gravimetric analysis (TGA) and CMT series microcomputer control electronic tensile testing machine. The results show that the crystallization degree PGA reaches 58.4% with the melting temperature between 222.48 ℃~223.48 ℃, the highest elastic modulus is 1430.19MPa,and the highest tensile strength is 130.51 MPa.

    参考文献
    相似文献
    引证文献
引用本文

袁希萌,崔爱军,陈 群,何明阳,叶东伟,鲁康伟.双螺杆挤出法连续化制备聚乙交酯及性能表征[J].高分子材料科学与工程,2014,30(5):113-117. Ximeng Yuan, Aijun Cui, Qun Chen, Mingyang He, Dongwei Ye, Kangwei Lu. Characterization of Properties of Polyglycolide Continuously Prepared by Twin Screw Extruder[J]. Polymer Materials Science & Engineering,2014,30(5):113-117.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2014-05-15
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司