薄膜反应器中UV 光引发丙烯酰胺反相乳液连续聚合过程
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

山西省自然科学基金资助项目(2012011008-2)


Continuous Polymerization of Acrylamide Inverse Emulsion in Thin Film Reactor by UV Radiation
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    报道了薄膜反应器在UV光直接引发丙烯酰胺(AM)反相乳液聚合中的应用。以OP-10/Span-80为复合乳化剂,环己烷为溶剂,在室温且不使用引发剂,采用UV光直接引发AM 反相乳液聚合,所得聚合物相对分子质量达107。考察了单体浓度、光照强度、液体流量、转速等因素对聚合反应的影响。结果表明,单体浓度增加,聚合物相对分子质量提高,聚合速率先增加后减小;随着光强的增大,单体转化率和聚合速率增加,而聚合物相对分子质量下降;随着转速的增加,单体转化率和相对分子质量先增加后降低,当转速为300r/min时达到最大值。通过调节转盘转速和原料流量得到最优停留时间。

    Abstract:

    The thin liquid film spinning disc reactor was used in opaque inverse emulsion polymerization of acrylamide (AM) by UV radiation. Using OP-10/span-80 as blend emulsifier, cyclohexane as solvent, in the absence of initiator and under UV initiation, the polymerizations of AM inverse emulsion system were successfully accomplished at low temperature,and the molecular weight of PAM is 107. The effects of monomer concentration, UV intensity, feed rate and rotational speed on polymerization were investigated. The results show that the molecular weight increases when the monomer concentration increases, and the polymerization rate increases at first and then decreases. The polymerization rate increases while molecular weights decrease with increase of the light intensity. When the rotational speed increases, both conversion and molecular weight increase at first and then decrease, reach the maximum with the rotation speed of 300 r/min. Optimum residence time was obtained by adjusting rotational speed and feed rate.

    参考文献
    相似文献
    引证文献
引用本文

张巧玲,李小月,郑会敏,刘有智.薄膜反应器中UV 光引发丙烯酰胺反相乳液连续聚合过程[J].高分子材料科学与工程,2014,30(6):20-23. Qiaoling Zhang, Xiaoyue Li, Huimin Zheng, Youzhi Liu. Continuous Polymerization of Acrylamide Inverse Emulsion in Thin Film Reactor by UV Radiation[J]. Polymer Materials Science & Engineering,2014,30(6):20-23.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2014-06-16
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司